Independent Submission D. Savage Request for Comments: 7868 J. Ng Category: Informational S. Moore ISSN: 2070-1721 Cisco Systems D. Slice Cumulus Networks P. Paluch University of Zilina R. White LinkedIn May 2016 Cisco's Enhanced Interior Gateway Routing Protocol (EIGRP) Abstract This document describes the protocol design and architecture for Enhanced Interior Gateway Routing Protocol (EIGRP). EIGRP is a routing protocol based on Distance Vector technology. The specific algorithm used is called "DUAL", a Diffusing Update Algorithm as referenced in "Loop-Free Routing Using Diffusing Computations" (Garcia-Luna-Aceves 1993). The algorithm and procedures were researched, developed, and simulated by SRI International. Status of This Memo This document is not an Internet Standards Track specification; it is published for informational purposes. This is a contribution to the RFC Series, independently of any other RFC stream. The RFC Editor has chosen to publish this document at its discretion and makes no statement about its value for implementation or deployment. Documents approved for publication by the RFC Editor are not a candidate for any level of Internet Standard; see Section 2 of RFC 5741. Information about the current status of this document, any errata, and how to provide feedback on it may be obtained at http://www.rfc-editor.org/info/rfc7868. Savage, et al. Informational [Page 1] RFC 7868 Cisco's EIGRP May 2016 Copyright Notice Copyright (c) 2016 IETF Trust and the persons identified as the document authors. All rights reserved. This document is subject to BCP 78 and the IETF Trust's Legal Provisions Relating to IETF Documents (http://trustee.ietf.org/license-info) in effect on the date of publication of this document. Please review these documents carefully, as they describe your rights and restrictions with respect to this document. This document may not be modified, and derivative works of it may not be created, except to format it for publication as an RFC or to translate it into languages other than English. Table of Contents 1. Introduction ....................................................5 2. Conventions .....................................................5 2.1. Requirements Language ......................................5 2.2. Terminology ................................................5 3. The Diffusing Update Algorithm (DUAL) ...........................9 3.1. Algorithm Description ......................................9 3.2. Route States ..............................................10 3.3. Feasibility Condition .....................................11 3.4. DUAL Message Types ........................................13 3.5. DUAL Finite State Machine (FSM) ...........................13 3.6. DUAL Operation -- Example Topology ........................18 4. EIGRP Packets ..................................................20 4.1. UPDATE Packets ............................................21 4.2. QUERY Packets .............................................21 4.3. REPLY Packets .............................................22 4.4. Exception Handling ........................................22 4.4.1. Active Duration (SIA) ..............................22 4.4.1.1. SIA-QUERY .................................23 4.4.1.2. SIA-REPLY .................................24 5. EIGRP Operation ................................................25 5.1. Finite State Machine ......................................25 5.2. Reliable Transport Protocol ...............................25 5.2.1. Bandwidth on Low-Speed Links .......................32 5.3. Neighbor Discovery/Recovery ...............................32 5.3.1. Neighbor Hold Time .................................32 5.3.2. HELLO Packets ......................................33 5.3.3. UPDATE Packets .....................................33 5.3.4. Initialization Sequence ............................34 5.3.5. Neighbor Formation .................................35 5.3.6. QUERY Packets during Neighbor Formation ............35 Savage, et al. Informational [Page 2] RFC 7868 Cisco's EIGRP May 2016 5.4. Topology Table ............................................36 5.4.1. Route Management ...................................36 5.4.1.1. Internal Routes ...........................37 5.4.1.2. External Routes ...........................37 5.4.2. Split Horizon and Poison Reverse ...................38 5.4.2.1. Startup Mode ..............................38 5.4.2.2. Advertising Topology Table Change .........39 5.4.2.3. Sending a QUERY/UPDATE ....................39 5.5. EIGRP Metric Coefficients .................................39 5.5.1. Coefficients K1 and K2 .............................40 5.5.2. Coefficient K3 .....................................40 5.5.3. Coefficients K4 and K5 .............................40 5.5.4. Coefficient K6 .....................................41 5.5.4.1. Jitter ....................................41 5.5.4.2. Energy ....................................41 5.6. EIGRP Metric Calculations .................................41 5.6.1. Classic Metrics ....................................41 5.6.1.1. Classic Composite Formulation .............42 5.6.1.2. Cisco Interface Delay Compatibility .......43 5.6.2. Wide Metrics .......................................43 5.6.2.1. Wide Metric Vectors .......................44 5.6.2.2. Wide Metric Conversion Constants ..........45 5.6.2.3. Throughput Calculation ....................45 5.6.2.4. Latency Calculation .......................46 5.6.2.5. Composite Calculation .....................46 6. EIGRP Packet Formats ...........................................46 6.1. Protocol Number ...........................................46 6.2. Protocol Assignment Encoding ..............................47 6.3. Destination Assignment Encoding ...........................47 6.4. EIGRP Communities Attribute ...............................48 6.5. EIGRP Packet Header .......................................49 6.6. EIGRP TLV Encoding Format .................................51 6.6.1. Type Field Encoding ................................52 6.6.2. Length Field Encoding ..............................52 6.6.3. Value Field Encoding ...............................52 6.7. EIGRP Generic TLV Definitions .............................52 6.7.1. 0x0001 - PARAMETER_TYPE ............................53 6.7.2. 0x0002 - AUTHENTICATION_TYPE .......................53 6.7.2.1. 0x02 - MD5 Authentication Type ............54 6.7.2.2. 0x03 - SHA2 Authentication Type ...........54 6.7.3. 0x0003 - SEQUENCE_TYPE .............................54 6.7.4. 0x0004 - SOFTWARE_VERSION_TYPE .....................55 6.7.5. 0x0005 - MULTICAST_SEQUENCE_TYPE ...................55 6.7.6. 0x0006 - PEER_INFORMATION_TYPE .....................55 6.7.7. 0x0007 - PEER_ TERMINATION_TYPE ....................56 6.7.8. 0x0008 - TID_LIST_TYPE .............................56 6.8. Classic Route Information TLV Types .......................57 6.8.1. Classic Flag Field Encoding ........................57 Savage, et al. Informational [Page 3] RFC 7868 Cisco's EIGRP May 2016 6.8.2. Classic Metric Encoding ............................57 6.8.3. Classic Exterior Encoding ..........................58 6.8.4. Classic Destination Encoding .......................59 6.8.5. IPv4-Specific TLVs .................................59 6.8.5.1. IPv4 INTERNAL_TYPE ........................60 6.8.5.2. IPv4 EXTERNAL_TYPE ........................60 6.8.5.3. IPv4 COMMUNITY_TYPE .......................62 6.8.6. IPv6-Specific TLVs .................................62 6.8.6.1. IPv6 INTERNAL_TYPE ........................63 6.8.6.2. IPv6 EXTERNAL_TYPE ........................63 6.8.6.3. IPv6 COMMUNITY_TYPE .......................65 6.9. Multiprotocol Route Information TLV Types .................66 6.9.1. TLV Header Encoding ................................66 6.9.2. Wide Metric Encoding ...............................67 6.9.3. Extended Metrics ...................................68 6.9.3.1. 0x00 - NoOp ...............................69 6.9.3.2. 0x01 - Scaled Metric ......................70 6.9.3.3. 0x02 - Administrator Tag ..................70 6.9.3.4. 0x03 - Community List .....................71 6.9.3.5. 0x04 - Jitter .............................71 6.9.3.6. 0x05 - Quiescent Energy ...................71 6.9.3.7. 0x06 - Energy .............................72 6.9.3.8. 0x07 - AddPath ............................72 6.9.3.8.1. AddPath with IPv4 Next Hop .....73 6.9.3.8.2. AddPath with IPv6 Next Hop .....74 6.9.4. Exterior Encoding ..................................75 6.9.5. Destination Encoding ...............................76 6.9.6. Route Information ..................................76 6.9.6.1. INTERNAL TYPE .............................76 6.9.6.2. EXTERNAL TYPE .............................76 7. Security Considerations ........................................77 8. IANA Considerations ............................................77 9. References .....................................................77 9.1. Normative References ......................................77 9.2. Informative References ....................................78 Acknowledgments ...................................................79 Authors' Addresses ................................................80 Savage, et al. Informational [Page 4] RFC 7868 Cisco's EIGRP May 2016 1. Introduction This document describes the Enhanced Interior Gateway Routing Protocol (EIGRP), a routing protocol designed and developed by Cisco Systems, Inc. DUAL, the algorithm used to converge the control plane to a single set of loop-free paths is based on research conducted at SRI International [3]. The Diffusing Update Algorithm (DUAL) is the algorithm used to obtain loop freedom at every instant throughout a route computation [2]. This allows all routers involved in a topology change to synchronize at the same time; the routers not affected by topology changes are not involved in the recalculation. This document describes the protocol that implements these functions. 2. Conventions 2.1. Requirements Language The key words "MUST", "MUST NOT", "REQUIRED", "SHALL", "SHALL NOT", "SHOULD", "SHOULD NOT", "RECOMMENDED", "MAY", and "OPTIONAL" in this document are to be interpreted as described in RFC 2119 [1]. 2.2. Terminology The following is a list of abbreviations and terms used throughout this document: ACTIVE State: The local state of a route on a router triggered by any event that causes all neighbors providing the current least-cost path to fail the Feasibility Condition check. A route in Active state is considered unusable. During Active state, the router is actively attempting to compute the least-cost loop-free path by explicit coordination with its neighbors using Query and Reply messages. Address Family Identifier (AFI): Identity of the network-layer protocol reachability information being advertised [12]. Autonomous System (AS): A collection of routers exchanging routes under the control of one or more network administrators on behalf of a single administrative entity. Savage, et al. Informational [Page 5] RFC 7868 Cisco's EIGRP May 2016 Base Topology: A routing domain representing a physical (non-virtual) view of the network topology consisting of attached devices and network segments EIGRP uses to form neighbor relationships. Destinations exchanged within the Base Topology are identified with a Topology Identifier value of zero (0). Computed Distance (CD): Total distance (metric) along a path from the current router to a destination network through a particular neighbor computed using that neighbor's Reported Distance (RD) and the cost of the link between the two routers. Exactly one CD is computed and maintained per the [Destination, Advertising Neighbor] pair. CR-Mode Conditionally Received Mode Diffusing Computation: A distributed computation in which a single starting node commences the computation by delegating subtasks of the computation to its neighbors that may, in turn, recursively delegate sub-subtasks further, including a signaling scheme allowing the starting node to detect that the computation has finished while avoiding false terminations. In DUAL, the task of coordinated updates of routing tables and resulting best path computation is performed as a diffusing computation. Diffusing Update Algorithm (DUAL): A loop-free routing algorithm used with distance vectors or link states that provides a diffused computation of a routing table. It works very well in the presence of multiple topology changes with low overhead. The technology was researched and developed at SRI International [3]. Downstream Router: A router that is one or more hops away from the router in question in the direction of the destination. EIGRP: Enhanced Interior Gateway Routing Protocol. Feasibility Condition: The Feasibility Condition is a sufficient condition used by a router to verify whether a neighboring router provides a loop-free path to a destination. EIGRP uses the Source Node Condition stating that a neighboring router meets the Feasibility Condition if the neighbor's RD is less than this router's Feasible Distance. Savage, et al. Informational [Page 6] RFC 7868 Cisco's EIGRP May 2016 Feasible Distance (FD): Defined as the least-known total metric to a destination from the current router since the last transition from ACTIVE to PASSIVE state. Being effectively a record of the smallest known metric since the last time the network entered the PASSIVE state, the FD is not necessarily a metric of the current best path. Exactly one FD is computed per destination network. Feasible Successor: A neighboring router that meets the Feasibility Condition for a particular destination, hence, providing a guaranteed loop-free path. Neighbor/Peer: For a particular router, another router toward which an EIGRP session, also known as an "adjacency", is established. The ability of two routers to become neighbors depends on their mutual connectivity and compatibility of selected EIGRP configuration parameters. Two neighbors with interfaces connected to a common subnet are known as adjacent neighbors. Two neighbors that are multiple hops apart are known as remote neighbors. PASSIVE state: The local state of a route in which at least one neighbor providing the current least-cost path passes the Feasibility Condition check. A route in PASSIVE state is considered usable and not in need of a coordinated re-computation. Network Layer Reachability Information (NLRI): Information a router uses to calculate the global routing table to make routing and forwarding decisions. Reported Distance (RD): For a particular destination, the value representing the router's distance to the destination as advertised in all messages carrying routing information. RD is not equivalent to the current distance of the router to the destination and may be different from it during the process of path re-computation. Exactly one RD is computed and maintained per destination network. Sub-Topology: For a given Base Topology, a sub-topology is characterized by an independent set of routers and links in a network for which EIGRP performs an independent path calculation. This allows each sub- topology to implement class-specific topologies to carry class- specific traffic. Savage, et al. Informational [Page 7] RFC 7868 Cisco's EIGRP May 2016 Successor: For a particular destination, a neighboring router that meets the Feasibility Condition and, at the same time, provides the least- cost path. Stuck In Active (SIA): A destination that has remained in the ACTIVE State in excess of a predefined time period at the local router (Cisco implements this as 3 minutes). Successor-Directed Acyclic Graph (SDAG): For a particular destination, a graph defined by routing table contents of individual routers in the topology, such that nodes of this graph are the routers themselves and a directed edge from router X to router Y exists if and only if router Y is router X's successor. After the network has converged, in the absence of topological changes, SDAG is a tree. Topology Change / Topology-Change Event: Any event that causes the CD for a destination through a neighbor to be added, modified, or removed. As an example, detecting a link-cost change, receiving any EIGRP message from a neighbor advertising an updated neighbor's RD. Topology Identifier (TID): A number that is used to mark prefixes as belonging to a specific sub-topology. Topology Table: A data structure used by EIGRP to store information about every known destination including, but not limited to, network prefix / prefix length, FD, RD of each neighbor advertising the destination, CD over the corresponding neighbor, and route state. Type, Length, Value (TLV): An encoding format for information elements used in EIGRP messages to exchange information. Each TLV-formatted information element consists of three generic fields: Type identifying the nature of information carried in this element, Length describing the length of the entire TLV triplet, and Value carrying the actual information. The Value field may, itself, be internally structured; this depends on the actual type of the information element. This format allows for extensibility and backward compatibility. Upstream Router: A router that is one or more hops away from the router in question, in the direction of the source of the information. Savage, et al. Informational [Page 8] RFC 7868 Cisco's EIGRP May 2016 VID: VLAN Identifier Virtual Routing and Forwarding (VRF): Independent Virtual Private Network (VPN) routing/forwarding tables that coexist within the same router at the same time. 3. The Diffusing Update Algorithm (DUAL) The Diffusing Update Algorithm (DUAL) constructs least-cost paths to all reachable destinations in a network consisting of nodes and edges (routers and links). DUAL guarantees that each constructed path is loop free at every instant including periods of topology changes and network reconvergence. This is accomplished by all routers, which are affected by a topology change, computing the new best path in a coordinated (diffusing) way and using the Feasibility Condition to verify prospective paths for loop freedom. Routers that are not affected by topology changes are not involved in the recalculation. The convergence time with DUAL rivals that of any other existing routing protocol. 3.1. Algorithm Description DUAL is used by EIGRP to achieve fast loop-free convergence with little overhead, allowing EIGRP to provide convergence rates comparable, and in some cases better than, most common link state protocols [10]. Only nodes that are affected by a topology change need to propagate and act on information about the topology change, allowing EIGRP to have good scaling properties, reduced overhead, and lower complexity than many other interior gateway protocols. Distributed routing algorithms are required to propagate information as well as coordinate information among all nodes in the network. Unlike basic Bellman-Ford distance vector protocols that rely on uncoordinated updates when a topology change occurs, DUAL uses a coordinated procedure to involve the affected part of the network into computing a new least-cost path, known as a "diffusing computation". A diffusing computation grows by querying additional routers for their current RD to the affected destination, and it shrinks by receiving replies from them. Unaffected routers send replies immediately, terminating the growth of the diffusing computation over them. These intrinsic properties cause the diffusing computation to self-adjust in scope and terminate as soon as possible. One attribute of DUAL is its ability to control the point at which the diffusion of a route calculation terminates by managing the distribution of reachability information through the network. Savage, et al. Informational [Page 9] RFC 7868 Cisco's EIGRP May 2016 Controlling the scope of the diffusing process is accomplished by hiding reachability information through aggregation (summarization), filtering, or other means. This provides the ability to create effective failure domains within a single AS, and allows the network administrator to manage the convergence and processing characteristics of the network. 3.2. Route States A route to a destination can be in one of two states: PASSIVE or ACTIVE. These states describe whether the route is guaranteed to be both loop free and the shortest available (the PASSIVE state) or whether such a guarantee cannot be given (the ACTIVE state). Consequently, in PASSIVE state, the router does not perform any route recalculation in coordination with its neighbors because no such recalculation is needed. In ACTIVE state, the router is actively involved in re-computing the least-cost loop-free path in coordination with its neighbors. The state is reevaluated and possibly changed every time a topology change is detected. A topology change is any event that causes the CD to the destination over any neighbor to be added, changed, or removed from EIGRP's topology table. More exactly, the two states are defined as follows: o Passive A route is considered to be in the Passive state when at least one neighbor that provides the current least-total-cost path passes the Feasibility Condition check that guarantees loop freedom. A route in the PASSIVE state is usable and its next hop is perceived to be a downstream router. o Active A route is considered to be in the ACTIVE state if neighbors that do not pass the Feasibility Condition check provide lowest-cost path, and therefore the path cannot be guaranteed loop free. A route in the ACTIVE state is considered unusable and this router must coordinate with its neighbors in the search for the new loop- free least-total-cost path. In other words, for a route to be in PASSIVE state, at least one neighbor that provides the least-total-cost path must be a Feasible Successor. Feasible Successors providing the least-total-cost path are also called "successors". For a route to be in PASSIVE state, at least one successor must exist. Savage, et al. Informational [Page 10] RFC 7868 Cisco's EIGRP May 2016 Conversely, if the path with the least total cost is provided by routers that are not Feasible Successors (and thus not successors), the route is in the ACTIVE state, requiring re-computation. Notably, for the definition of PASSIVE and ACTIVE states, it does not matter if there are Feasible Successors providing a worse-than-least- total-cost path. While these neighbors are guaranteed to provide a loop-free path, that path is potentially not the shortest available. The fact that the least-total-cost path can be provided by a neighbor that fails the Feasibility Condition check may not be intuitive. However, such a situation can occur during topology changes when the current least-total-cost path fails and the next-least-total-cost path traverses a neighbor that is not a Feasible Successor. While a router has a route in the ACTIVE state, it must not change its successor (i.e., modify the current SDAG) nor modify its own Feasible Distance or RD until the route enters the PASSIVE state again. Any updated information about this route received during ACTIVE state is reflected only in CDs. Any updates to the successor, FD, and RD are postponed until the route returns to PASSIVE state. The state transitions from PASSIVE to ACTIVE and from ACTIVE to PASSIVE are controlled by the DUAL FSM and are described in detail in Section 3.5. 3.3. Feasibility Condition The Feasibility Condition is a criterion used to verify loop freedom of a particular path. The Feasibility Condition is a sufficient but not a necessary condition, meaning that every path meeting the Feasibility Condition is guaranteed to be loop free; however, not all loop-free paths meet the Feasibility Condition. The Feasibility Condition is used as an integral part of DUAL operation: every path selection in DUAL is subject to the Feasibility Condition check. Based on the result of the Feasibility Condition check after a topology change is detected, the route may either remain PASSIVE (if, after the topology change, the neighbor providing the least cost path meets the Feasibility Condition) or it needs to enter the ACTIVE state (if the topology change resulted in none of the neighbors providing the least cost path to meet the Feasibility Condition). The Feasibility Condition is a part of DUAL that allows the diffused computation to terminate as early as possible. Nodes that are not affected by the topology change are not required to perform a DUAL computation and may not be aware a topology change occurred. This can occur in two cases: Savage, et al. Informational [Page 11] RFC 7868 Cisco's EIGRP May 2016 First, if informed about a topology change, a router may keep a route in PASSIVE state if it is aware of other paths that are downstream towards the destination (routes meeting the Feasibility Condition). A route that meets the Feasibility Condition is determined to be loop free and downstream along the path between the router and the destination. Second, if informed about a topology change for which it does not currently have reachability information, a router is not required to enter into the ACTIVE state, nor is it required to participate in the DUAL process. In order to facilitate describing the Feasibility Condition, a few definitions are in order. o A successor for a given route is the next hop used to forward data traffic for a destination. Typically, the successor is chosen based on the least-cost path to reach the destination. o A Feasible Successor is a neighbor that meets the Feasibility Condition. A Feasible Successor is regarded as a downstream neighbor towards the destination, but it may not be the least-cost path but could still be used for forwarding data packets in the event equal or unequal cost load sharing was active. A Feasible Successor can become a successor when the current successor becomes unreachable. o The Feasibility Condition is met when a neighbor's advertised cost, (RD) to a destination is less than the FD for that destination, or in other words, the Feasibility Condition is met when the neighbor is closer to the destination than the router itself has ever been since the destination has entered the PASSIVE state for the last time. o The FD is the lowest distance to the destination since the last time the route went from ACTIVE to PASSIVE state. It should be noted it is not necessarily the current best distance; rather, it is a historical record of the best distance known since the last diffusing computation for the destination has finished. Thus, the value of the FD can either be the same as the current best distance, or it can be lower. A neighbor that advertises a route with a cost that does not meet the Feasibility Condition may be upstream and thus cannot be guaranteed to be the next hop for a loop-free path. Routes advertised by upstream neighbors are not recorded in the routing table but saved in the topology table. Savage, et al. Informational [Page 12] RFC 7868 Cisco's EIGRP May 2016 3.4. DUAL Message Types DUAL operates with three basic message types: QUERY, UPDATE, and REPLY. o UPDATE - sent to indicate a change in metric or an addition of a destination. o QUERY - sent when the Feasibility Condition fails, which can happen for reasons like a destination becoming unreachable or the metric increasing to a value greater than its current FD. o REPLY - sent in response to a QUERY or SIA-QUERY In addition to these three basic types, two additional sub-types have been added to EIGRP: o SIA-QUERY - sent when a REPLY has not been received within one- half of the SIA interval (90 seconds as implemented by Cisco). o SIA-REPLY - sent in response to an SIA-QUERY indicating the route is still in ACTIVE state. This response does not stratify the original QUERY; it is only used to indicate that the sending neighbor is still in the ACTIVE state for the given destination. When in the PASSIVE state, a received QUERY may be propagated if there is no Feasible Successor found. If a Feasible Successor is found, the QUERY is not propagated and a REPLY is sent for the destination with a metric equal to the current routing table metric. When a QUERY is received from a non-successor in ACTIVE state, a REPLY is sent and the QUERY is not propagated. The REPLY for the destination contains a metric equal to the current routing table metric. 3.5. DUAL Finite State Machine (FSM) The DUAL FSM embodies the decision process for all route computations. It tracks all routes advertised by all neighbors. The distance information, known as a metric, is used by DUAL to select efficient loop-free paths. DUAL selects routes to be inserted into a routing table based on Feasible Successors. A successor is a neighboring router used for packet forwarding that has a least-cost path to a destination that is guaranteed not to be part of a routing loop. When there are no Feasible Successors but there are neighbors advertising the destination, a recalculation must occur to determine a new successor. Savage, et al. Informational [Page 13] RFC 7868 Cisco's EIGRP May 2016 The amount of time it takes to calculate the route impacts the convergence time. Even though the recalculation is not processor intensive, it is advantageous to avoid recalculation if it is not necessary. When a topology change occurs, DUAL will test for Feasible Successors. If there are Feasible Successors, it will use any it finds in order to avoid any unnecessary recalculation. The FSM, which applies per destination in the topology table, operates independently for each destination. It is true that if a single link goes down, multiple routes may go into ACTIVE state. However, a separate SDAG is computed for each destination, so loop- free topologies can be maintained for each reachable destination. Savage, et al. Informational [Page 14] RFC 7868 Cisco's EIGRP May 2016 +------------+ +-----------+ | \ / | | \ / | | +=================================+ | | | | | |(1)| Passive |(2)| +-->| |<--+ +=================================+ ^ | ^ ^ ^ | (14)| |(15)| |(13)| | | (4)| |(16)| | (3)| | | | | | +------------+ | | | | | \ +-------+ + + | +-------------+ \ / / / | \ \ / / / +----+ \ \ | | | | | | | v | | | v +==========+(11) +==========+ +==========+(12) +==========+ | Active |---->| Active |(5) | Active |---->| Active | | | (9)| |---->| | (10)| | | oij=0 |<----| oij=1 | | oij=2 |<----| oij=3 | +--| | +--| | +--| | +--| | | +==========+ | +==========+ | +==========+ | +==========+ | ^ |(5) | ^ | ^ ^ | ^ | | +-----|------|---------|----+ | | | +------+ +------+ +---------+ +---------+ (6,7,8) (6,7,8) (6,7,8) (6,7,8) Figure 1: DUAL Finite State Machine Legend: i Node that is computing route j Destination node or network k Any neighbor of node i oij QUERY origin flag 0 = metric increase during ACTIVE state 1 = node i originated 2 = QUERY from, or link increase to, successor during ACTIVE state 3 = QUERY originated from successor rijk REPLY status flag for each neighbor k for destination j 1 = awaiting REPLY 0 = received REPLY lik = the link connecting node i to neighbor k Savage, et al. Informational [Page 15] RFC 7868 Cisco's EIGRP May 2016 The following describes in detail the state/event/action transitions of the DUAL FSM. For all steps, the topology table is updated with the new metric information from either QUERY, REPLY, or UPDATE received. (1) A QUERY is received from a neighbor that is not the current successor. The route is currently in PASSIVE state. As the successor is not affected by the QUERY, and a Feasible Successor exists, the route remains in PASSIVE state. Since a Feasible Successor exists, a REPLY MUST be sent back to the originator of the QUERY. Any metric received in the QUERY from that neighbor is recorded in the topology table and the Feasibility Check (FC) is run to check for any change to current successor. (2) A directly connected interface changes state (connects, disconnects, or changes metric), or similarly an UPDATE or QUERY has been received with a metric change for an existing destination, the route will stay in the PASSIVE state if the current successor is not affected by the change, or it is no longer reachable and there is a Feasible Successor. In either case, an UPDATE is sent with the new metric information if it has changed. (3) A QUERY was received from a neighbor who is the current successor and no Feasible Successors exist. The route for the destination goes into ACTIVE state. A QUERY is sent to all neighbors on all interfaces that are not split horizon. Split horizon takes effect for a query or update from the successor it is using for the destination in the query. The QUERY origin flag is set to indicate the QUERY originated from a neighbor marked as successor for route. The REPLY status flag is set for all neighbors to indicate outstanding replies. (4) A directly connected link has gone down or its cost has increased, or an UPDATE has been received with a metric increase. The route to the destination goes to ACTIVE state if there are no Feasible Successors found. A QUERY is sent to all neighbors on all interfaces. The QUERY origin flag is to indicate that the router originated the QUERY. The REPLY status flag is set to 1 for all neighbors to indicate outstanding replies. Savage, et al. Informational [Page 16] RFC 7868 Cisco's EIGRP May 2016 (5) While a route for a destination is in ACTIVE state, and a QUERY is received from the current successor, the route remains in ACTIVE state. The QUERY origin flag is set to indicate that there was another topology change while in ACTIVE state. This indication is used so new Feasible Successors are compared to the metric that made the route go to ACTIVE state with the current successor. (6) While a route for a destination is in ACTIVE state and a QUERY is received from a neighbor that is not the current successor, a REPLY should be sent to the neighbor. The metric received in the QUERY should be recorded. (7) If a link cost changes, or an UPDATE with a metric change is received in ACTIVE state from a non-successor, the router stays in ACTIVE state for the destination. The metric information in the UPDATE is recorded. When a route is in the ACTIVE state, neither a QUERY nor UPDATE are ever sent. (8) If a REPLY for a destination, in ACTIVE state, is received from a neighbor or the link between a router and the neighbor fails, the router records that the neighbor replied to the QUERY. The REPLY status flag is set to 0 to indicate this. The route stays in ACTIVE state if there are more replies pending because the router has not heard from all neighbors. (9) If a route for a destination is in ACTIVE state, and a link fails or a cost increase occurred between a router and its successor, the router treats this case like it has received a REPLY from its successor. When this occurs after the router originates a QUERY, it sets the QUERY origin flag to indicate that another topology change occurred in ACTIVE state. (10) If a route for a destination is in ACTIVE state, and a link fails or a cost increase occurred between a router and its successor, the router treats this case like it has received a REPLY from its successor. When this occurs after a successor originated a QUERY, the router sets the QUERY origin flag to indicate that another topology change occurred in ACTIVE state. (11) If a route for a destination is in ACTIVE state, the cost of the link through which the successor increases, and the last REPLY was received from all neighbors, but there is no Feasible Successor, the route should stay in ACTIVE state. A QUERY is sent to all neighbors. The QUERY origin flag is set to 1. Savage, et al. Informational [Page 17] RFC 7868 Cisco's EIGRP May 2016 (12) If a route for a destination is in ACTIVE state because of a QUERY received from the current successor, and the last REPLY was received from all neighbors, but there is no Feasible Successor, the route should stay in ACTIVE state. A QUERY is sent to all neighbors. The QUERY origin flag is set to 3. (13) Received replies from all neighbors. Since the QUERY origin flag indicates the successor originated the QUERY, it transitions to PASSIVE state and sends a REPLY to the old successor. (14) Received replies from all neighbors. Since the QUERY origin flag indicates a topology change to the successor while in ACTIVE state, it need not send a REPLY to the old successor. When the Feasibility Condition is met, the route state transitions to PASSIVE. (15) Received replies from all neighbors. Since the QUERY origin flag indicates either the router itself originated the QUERY or FC was not satisfied with the replies received in ACTIVE state, FD is reset to infinite value and the minimum of all the reported metrics is chosen as FD and route transitions back to PASSIVE state. A REPLY is sent to the old-successor if oij flags indicate that there was a QUERY from successor. (16) If a route for a destination is in ACTIVE state because of a QUERY received from the current successor or there was an increase in distance while in ACTIVE state, the last REPLY was received from all neighbors, and a Feasible Successor exists for the destination, the route can go into PASSIVE state and a REPLY is sent to the successor if oij indicates that QUERY was received from the successor. 3.6. DUAL Operation -- Example Topology The following topology (Figure 2) will be used to provide an example of how DUAL is used to reroute after a link failure. Each node is labeled with its costs to destination N. The arrows indicate the successor (next hop) used to reach destination N. The least-cost path is selected. Savage, et al. Informational [Page 18] RFC 7868 Cisco's EIGRP May 2016 N | (1)A ---<--- B(2) | | ^ | | | (2)D ---<--- C(3) Figure 2: Stable Topology In the case where the link between A and D fails (Figure 3); N N | | A ---<--- B A ---<--- B | | | | X | ^ | | | | | D ---<--- C D ---<--- C Q-> <-R N | (1)A ---<--- B(2) | ^ | (4)D --->--- C(3) Figure 3: Link between A and D Fails Only observing the destination provided by node N, D enters the ACTIVE state and sends a QUERY to all its neighbors, in this case node C. C determines that it has a Feasible Successor and replies immediately with metric 3. C changes its old successor of D to its new single successor B and the route to N stays in PASSIVE state. D receives the REPLY and can transition out of ACTIVE state since it received replies from all its neighbors. D now has a viable path to N through C. D selects C as its successor to reach node N with a cost of 4. Notice that nodes A and B were not involved in the recalculation since they were not affected by the change. Savage, et al. Informational [Page 19] RFC 7868 Cisco's EIGRP May 2016 Let's consider the situation in Figure 4, where Feasible Successors may not exist. If the link between node A and B fails, B goes into ACTIVE state for destination N since it has no Feasible Successors. Node B sends a QUERY to node C. C has no Feasible Successors, so it goes active for destination N; and since C has no neighbors, it replies to the QUERY, deletes the destination, and returns to the PASSIVE state for the unreachable route. As C removes the (now unreachable) destination from its table, C sends REPLY to its old successor. B receives this REPLY from C, and determines this is the last REPLY it is waiting on before determining what the new state of the route should be; on receiving this REPLY, B deletes the route to N from its routing table. Since B was the originator of the initial QUERY, it does not have to send a REPLY to its old successor (it would not be able to any ways, because the link to its old successor is down). Note that nodes A and D were not involved in the recalculation since their successors were not affected. N N | | (1)A ---<--- B(2) A ------- B Q | | | | |^ ^ ^ ^ ^ | v| | | | | | | | (2)D C(3) D C ACK R Figure 4: No Feasible Successors When Link between A and B Fails 4. EIGRP Packets EIGRP uses five different packet types to handle session management and pass DUAL Message types: HELLO Packets (includes ACK) QUERY Packets (includes SIA-Query) REPLY Packets (includes SIA-Reply) REQUEST Packets UPDATE Packets EIGRP packets are directly encapsulated into a network-layer protocol, such as IPv4 or IPv6. While EIGRP is capable of using additional encapsulation (such as AppleTalk, IPX, etc.) no further encapsulation is specified in this document. Savage, et al. Informational [Page 20] RFC 7868 Cisco's EIGRP May 2016 Support for network-layer protocol fragmentation is not supported, and EIGRP will attempt to avoid a maximum size packets that exceed the interface MTU by sending multiple packets that are less than or equal to MTU-sized packets. Each packet transmitted will use either multicast or unicast network- layer destination addresses. When multicast addresses are used, a mapping for the data link multicast address (when available) must be provided. The source address will be set to the address of the sending interface, if applicable. The following network-layer multicast addresses and associated data link multicast addresses: 224.0.0.10 for IPv4 "EIGRP Routers" [13] FF02:0:0:0:0:0:0:A for IPv6 "EIGRP Routers" [14] They will be used on multicast-capable media and will be media independent for unicast addresses. Network-layer addresses will be used and the mapping to media addresses will be achieved by the native protocol mechanisms. 4.1. UPDATE Packets UPDATE packets carry the DUAL UPDATE message type and are used to convey information about destinations and the reachability of those destinations. When a new neighbor is discovered, unicast UPDATE packets are used to transmit a full table to the new neighbor, so the neighbor can build up its topology table. In normal operation (other than neighbor startup such as a link cost changes), UPDATE packets are multicast. UPDATE packets are always transmitted reliably. Each TLV destination will be processed individually through the DUAL FSM. 4.2. QUERY Packets A QUERY packet carries the DUAL QUERY message type and is sent by a router to advertise that a route is in ACTIVE state and the originator is requesting alternate path information from its neighbors. An infinite metric is encoded by setting the delay part of the metric to its maximum value. If there is a topology change that causes multiple destinations to be marked ACTIVE, EIGRP will build one or more QUERY packets for all destinations present. The state of each route is recorded individually, so a responding QUERY or REPLY need not contain all the same destinations in a single packet. Since EIGRP uses a reliable transport mechanism, route QUERY packets are also guaranteed be reliably delivered. Savage, et al. Informational [Page 21] RFC 7868 Cisco's EIGRP May 2016 When a QUERY packet is received, each destination will trigger a DUAL event, and the state machine will run individually for each route. Once the entire original QUERY packet is processed, then a REPLY or SIA-REPLY will be sent with the latest information. 4.3. REPLY Packets A REPLY packet carries the DUAL REPLY message type and will be sent in response to a QUERY or SIA-QUERY packet. The REPLY packet will include a TLV for each destination and the associated vector metric in its own topology table. The REPLY packet is sent after the entire received QUERY packet is processed. When a REPLY packet is received, there is no reason to process the packet before an acknowledgment is sent. Therefore, an acknowledgment is sent immediately and then the packet is processed. The sending of the acknowledgment is accomplished either by sending an ACK packet or by piggybacking the acknowledgment onto another packet already being transmitted. Each TLV destination will be processed individually through the DUAL FSM. When a QUERY is received for a route that doesn't exist in our topology table, a REPLY with an infinite metric is sent and an entry in the topology table is added with the metric in the QUERY if the metric is not an infinite value. If a REPLY for a designation not in the Active state, or not in the topology table, EIGRP will acknowledge the packet and discard the REPLY. 4.4. Exception Handling 4.4.1. Active Duration (SIA) When an EIGRP router transitions to ACTIVE state for a particular destination, a QUERY is sent to a neighbor and the ACTIVE timer is started to limit the amount of time a destination may remain in an ACTIVE state. A route is regarded as SIA when it does not receive a REPLY within a preset time. This time interval is broken into two equal periods following the QUERY, and up to three additional "busy" periods in which an SIA-QUERY packet is sent for the destination. This process is begun when a router sends a QUERY to its neighbor. After one-half the SIA time interval (default implementation is 90 seconds), the router will send an SIA-QUERY; this must be replied to with either a REPLY or SIA-REPLY. Any neighbor that fails to send Savage, et al. Informational [Page 22] RFC 7868 Cisco's EIGRP May 2016 either a REPLY or SIA-REPLY with-in one-half the SIA interval will result in the neighbor being deemed to be "stuck" in the active state. Cisco also limits the number of SIA-REPLY messages allowed to three. Once the timeout occurs after the third SIA-REPLY with the neighbor remaining in an ACTIVE state (as noted in the SIA-Reply message), the neighbor being deemed to be "stuck" in the active state. If the SIA state is declared, DUAL may take one of two actions; a) Delete the route from that neighbor, acting as if the neighbor had responded with an unreachable REPLY message from the neighbor. b) Delete all routes from that neighbor and reset the adjacency with that neighbor, acting as if the neighbor had responded with an unreachable message for all routes. Implementation note: Cisco currently implements option (b). 4.4.1.1. SIA-QUERY When a QUERY is still outstanding and awaiting a REPLY from a neighbor, there is insufficient information to determine why a REPLY has not been received. A lost packet, congestion on the link, or a slow neighbor could cause a lack of REPLY from a downstream neighbor. In order to try to ascertain if the neighboring device is still attempting to converge on the active route, EIGRP may send an SIA- QUERY packet to the active neighbor(s). This enables an EIGRP router to determine if there is a communication issue with the neighbor or if it is simply still attempting to converge with downstream routers. By sending an SIA-QUERY, the originating router may extend the effective active time by resetting the ACTIVE timer that has been previously set, thus allowing convergence to continue so long as neighbor devices successfully communicate that convergence is still underway. The SIA-QUERY packet SHOULD be sent on a per-destination basis at one-half of the ACTIVE timeout period. Up to three SIA-QUERY packets for a specific destination may be sent, each at a value of one-half the ACTIVE time, so long as each are successfully acknowledged and met with an SIA-REPLY. Savage, et al. Informational [Page 23] RFC 7868 Cisco's EIGRP May 2016 Upon receipt of an SIA-QUERY packet, an EIGRP router should first send an ACK and then continue to process the SIA-QUERY information. The QUERY is sent on a per-destination basis at approximately one- half the active time. If the EIGRP router is still active for the destination specified in the SIA-QUERY, the router should respond to the originator with the SIA-REPLY indicating that active processing for this destination is still underway by setting the ACTIVE flag in the packet upon response. If the router receives an SIA-QUERY referencing a destination for which it has not received the original QUERY, the router should treat the packet as though it was a standard QUERY: 1) Acknowledge the receipt of the packet 2) Send a REPLY if a successor exists 3) If the SIA-QUERY is from the successor, transition to the ACTIVE state if and only if a Feasibility Condition check fails and send an SIA-REPLY with the ACTIVE bit set 4.4.1.2. SIA-REPLY An SIA-REPLY packet is the corresponding response upon receipt of an SIA-QUERY from an EIGRP neighbor. The SIA-REPLY packet will include a TLV for each destination and the associated vector metric in the topology table. The SIA-REPLY packet is sent after the entire received SIA-QUERY packet is processed. If the EIGRP router is still ACTIVE for a destination, the SIA-REPLY packet will be sent with the ACTIVE bit set. This confirms for the neighbor device that the SIA-QUERY packet has been processed by DUAL and that the router is still attempting to resolve a loop-free path (likely awaiting responses to its own QUERY to downstream neighbors). The SIA-REPLY informs the recipient that convergence is complete or still ongoing; it is an explicit notification that the router is still actively engaged in the convergence process. This allows the device that sent the SIA-QUERY to determine whether it should continue to allow the routes that are not converged to be in the ACTIVE state or if it should reset the neighbor relationship and flush all routes through this neighbor. Savage, et al. Informational [Page 24] RFC 7868 Cisco's EIGRP May 2016 5. EIGRP Operation EIGRP has four basic components: o Finite State Machine o Reliable Transport Protocol o Neighbor Discovery/Recovery o Route Management 5.1. Finite State Machine The detail of DUAL, the State Machine used by EIGRP, is covered in Section 3.5. 5.2. Reliable Transport Protocol The reliable transport is responsible for guaranteed, ordered delivery of EIGRP packets to all neighbors. It supports intermixed transmission of multicast and unicast packets. Some EIGRP packets must be transmitted reliably and others need not. For efficiency, reliability is provided only when necessary. For example, on a multi-access network that has multicast capabilities, such as Ethernet, it is not necessary to send HELLOs reliably to all neighbors individually. EIGRP sends a single multicast HELLO with an indication in the packet informing the receivers that the packet need not be acknowledged. Other types of packets, such as UPDATE packets, require acknowledgment and this is indicated in the packet. The reliable transport has a provision to send multicast packets quickly when there are unacknowledged packets pending. This helps ensure that convergence time remains low in the presence of varying speed links. DUAL assumes there is lossless communication between devices and thus must depend on the transport protocol to guarantee that messages are transmitted reliably. EIGRP implements the reliable transport protocol to ensure ordered delivery and acknowledgment of any messages requiring reliable transmission. State variables such as a received sequence number, acknowledgment number, and transmission queues MUST be maintained on a per-neighbor basis. Savage, et al. Informational [Page 25] RFC 7868 Cisco's EIGRP May 2016 The following sequence number rules must be met for the EIGRP reliable transport protocol to work correctly: o A sender of a packet includes its global sequence number in the sequence number field of the fixed header. The sequence number wraps around to one when the maximum value is exceeded (sequence number zero is reserved for unreliable transmission). The sender includes the receivers sequence number in the acknowledgment number field of the fixed header. o Any packets that do not require acknowledgment must be sent with a sequence number of 0. o Any packet that has an acknowledgment number of 0 indicates that sender is not expecting to explicitly acknowledge delivery. Otherwise, it is acknowledging a single packet. o Packets that are network-layer multicast must contain acknowledgment number of 0. When a router transmits a packet, it increments its sequence number and marks the packet as requiring acknowledgment by all neighbors on the interface for which the packet is sent. When individual acknowledgments are unicast addressed by the receivers to the sender with the acknowledgment number equal to the packets sequence number, the sender SHALL clear the pending acknowledgment requirement for the packet from the respective neighbor. If the required acknowledgment is not received for the packet, it MUST be retransmitted. Retransmissions will occur for a maximum of 5 seconds. This retransmission for each packet is tried 16 times, after which, if there is no ACK, the neighbor relationship is reset with the peer that didn't send the ACK. The protocol has no explicit windowing support. A receiver will acknowledge each packet individually and will drop packets that are received out of order. Implementation note: The exception to this occurs if a duplicate packet is received, and the acknowledgment for the original packet has been scheduled for transmission, but not yet sent. In this case, EIGRP will not send an acknowledgment for the duplicate packet, and the queued acknowledgment will acknowledge both the original and duplicate packet. Duplicate packets are also discarded upon receipt. Acknowledgments are not accumulative. Therefore, an ACK with a non-zero sequence number acknowledges a single packet. Savage, et al. Informational [Page 26] RFC 7868 Cisco's EIGRP May 2016 There are situations when multicast and unicast packets are transmitted close together on multi-access broadcast-capable networks. The reliable transport mechanism MUST ensure that all multicasts are transmitted in order and not mix the order among unicast and multicast packets. The reliable transport provides a mechanism to deliver multicast packets in order to some receivers quickly, while some receivers have not yet received all unicast or previously sent multicast packets. The SEQUENCE_TYPE TLV in HELLO packets achieves this. This will be explained in more detail in this section. Figure 5 illustrates the reliable transport protocol on point-to- point links. There are two scenarios that may occur: an UPDATE- initiated packet exchange or a QUERY-initiated packet exchange. This example will assume no packet loss. Router A Router B An Example UPDATE Exchange <---------------- UPDATE (multicast) A receives packet SEQ=100, ACK=0 Add packet to A's retransmit list ----------------> ACK (unicast) SEQ=0, ACK=100 Receive ACK Process UPDATE Delete packet from A's retransmit list An Example QUERY Exchange <---------------- QUERY (multicast) A receives packet SEQ=101, ACK=0 Process QUERY Add packet to A's retransmit list ----------------> REPLY (unicast) SEQ=201, ACK=101 Process ACK Delete packet from A's retransmit list Process REPLY packet <---------------- ACK (unicast) A receives packet SEQ=0, ACK=201 Figure 5: Reliable Transfer on Point-to-Point Links Savage, et al. Informational [Page 27] RFC 7868 Cisco's EIGRP May 2016 The UPDATE exchange sequence requires UPDATE packets sent to be delivered reliably. The UPDATE packet transmitted contains a sequence number that is acknowledged by a receipt of an ACK packet. If the UPDATE or the ACK packet is lost on the network, the UPDATE packet will be retransmitted. This example will assume there is heavy packet loss on a network. Router A Router B <---------------- UPDATE (multicast) A receives packet SEQ=100, ACK=0 Add packet to A's retransmit list ----------------> ACK (unicast) SEQ=0, ACK=100 Receive ACK Process UPDATE Delete packet from A's retransmit list <--/LOST/-------------- UPDATE (multicast) SEQ=101, ACK=0 Add packet to A's retransmit list Retransmit Timer Expires <---------------- Retransmit UPDATE (unicast) SEQ=101, ACK=0 Keep packet on A's retransmit list ----------------> ACK (unicast) SEQ=0, ACK=101 Receive ACK Process UPDATE Delete packet from A's retransmit list Figure 6: Reliable Transfer on Lossy Point-to-Point Links Reliable delivery on multi-access LANs works in a similar fashion to point-to-point links. The initial packet is always multicast and subsequent retransmissions are unicast addressed. The acknowledgments sent are always unicast addressed. Figure 7 shows an example with four routers on an Ethernet. Router B -----------+ | Router C -----------+------------ Router A | Router D -----------+ Savage, et al. Informational [Page 28] RFC 7868 Cisco's EIGRP May 2016 An Example UPDATE Exchange <---------------- A send UPDATE (multicast) SEQ=100, ACK=0 Add packet to B's retransmit list Add packet to C's retransmit list Add packet to D's retransmit list ----------------> B sends ACK (unicast) SEQ=0, ACK=100 Receive ACK Process UPDATE Delete packet from B's retransmit list ----------------> C sends ACK (unicast) SEQ=0, ACK=100 Receive ACK Process UPDATE Delete packet from C's retransmit list ----------------> D sends ACK (unicast) SEQ=0, ACK=100 Receive ACK Process UPDATE Delete packet from D's retransmit list An Example QUERY Exchange <---------------- A sends UPDATE (multicast) SEQ=101, ACK=0 Add packet to B's retransmit list Add packet to C's retransmit list Add packet to D's retransmit list ----------------> B sends REPLY (unicast) <---------------- SEQ=511, ACK=101 A sends ACK (unicast to B) Process UPDATE SEQ=0, ACK=511 Delete packet from B's retransmit list ----------------> C sends REPLY (unicast) <---------------- SEQ=200, ACK=101 A sends ACK (unicast to C) Process UPDATE SEQ=0, ACK=200 Delete packet from C's retransmit list ----------------> D sends REPLY (unicast) <---------------- SEQ=11, ACK=101 A sends ACK (unicast to D) Process UPDATE SEQ=0, ACK=11 Delete packet from D's retransmit list Figure 7: Reliable Transfer on Multi-Access Links Savage, et al. Informational [Page 29] RFC 7868 Cisco's EIGRP May 2016 And finally, a situation where numerous multicast and unicast packets are sent close together in a multi-access environment is illustrated in Figure 8. Router B -----------+ | Router C -----------+------------ Router A | Router D -----------+ <---------------- A sends UPDATE (multicast) SEQ=100, ACK=0 ---------------/LOST/-> Add packet to B's retransmit list B sends ACK (unicast) Add packet to C's retransmit list SEQ=0, ACK=100 Add packet to D's retransmit list ----------------> C sends ACK (unicast) SEQ=0, ACK=100 Delete packet from C's retransmit list ----------------> D sends ACK (unicast) SEQ=0, ACK=100 Delete packet from D's retransmit list <---------------- A sends HELLO (multicast) SEQ=0, ACK=0, SEQ_TLV listing B B receives Hello, does not set CR-Mode C receives Hello, sets CR-Mode D receives Hello, sets CR-Mode <---------------- A sends UPDATE (multicast) SEQ=101, ACK=0, CR-Flag=1 ---------------/LOST/-> Add packet to B's retransmit list B sends ACK (unicast) Add packet to C's retransmit list SEQ=0, ACK=100 Add packet to D's retransmit list B ignores UPDATE 101 because the CR-Flag is set and it is not in CR-Mode ----------------> C sends ACK (unicast) SEQ=0, ACK=101 Savage, et al. Informational [Page 30] RFC 7868 Cisco's EIGRP May 2016 ----------------> D sends ACK (unicast) SEQ=0, ACK=101 <---------------- A resends UPDATE (unicast to B) SEQ=100, ACK=0 B packet duplicate ---------------> B sends ACK (unicast) A removes packet from retransmit list SEQ=0, ACK=100 <---------------- A resends UPDATE (unicast to B) SEQ=101, ACK=0 ---------------> B sends ACK (unicast) A removes packet from retransmit list SEQ=0, ACK=101 Figure 8: Reliable Transfer on Multi-Access Links with Conditional Receive Initially, Router A sends a multicast addressed UPDATE packet on the LAN. B and C receive it and send acknowledgments. Router B receives the UPDATE, but the acknowledgment sent is lost on the network. Before the retransmission timer for Router B's packet expires, there is an event that causes a new multicast addressed UPDATE to be sent. Router A detects that there is at least one neighbor on the interface with a full queue. Therefore, it MUST signal that neighbor not to receive the next packet or it would receive the retransmitted packet out of order. If all neighbors on the interface have a full queue, then EIGRP should reschedule the transmission of the UPDATE once the queues are no longer full. Router A builds a HELLO packet with a SEQUENCE_TYPE TLV indicating all the neighbors that have full queues. In this case, the only neighbor address in the list is Router B. The HELLO packet is sent via multicast unreliably out the interface. Routers C and D process the SEQUENCE_TYPE TLV by looking for their own addresses in the list. If not found, they put themselves in CR- Mode. Router B does not find its address in the SEQUENCE TLV peer list, so it enters CR-Mode. Packets received by Router B with the CR-Flag MUST be discarded and not acknowledged. Savage, et al. Informational [Page 31] RFC 7868 Cisco's EIGRP May 2016 Later, Router A will unicast transmit both packets 100 and 101 directly to Router B. Router B already has 100, so it discards and acknowledges it. Router B then accepts and acknowledges packet 101. Once an acknowledgment is received, Router A can remove both packets from Router B's transmission list. 5.2.1. Bandwidth on Low-Speed Links By default, EIGRP limits itself to using no more than 50% of the bandwidth reported by an interface when determining packet-pacing intervals. If the bandwidth does not match the physical bandwidth (the network architect may have put in an artificially low or high bandwidth value to influence routing decisions), EIGRP may: 1. Generate more traffic than the interface can handle, possibly causing drops, thereby impairing EIGRP performance. 2. Generate a lot of EIGRP traffic that could result in little bandwidth remaining for user data. To control such transmissions, an interface-pacing timer is defined for the interfaces on which EIGRP is enabled. When a pacing timer expires, a packet is transmitted out on that interface. 5.3. Neighbor Discovery/Recovery Neighbor Discovery/Recovery is the process that routers use to dynamically learn of other routers on their directly attached networks. Routers MUST also discover when their neighbors become unreachable or inoperative. This process is achieved with low overhead by periodically sending small HELLO packets. As long as any packets are received from a neighbor, the router can determine that neighbor is alive and functioning. Only after a neighbor router is considered operational can the neighboring routers exchange routing information. 5.3.1. Neighbor Hold Time Each router keeps state information about adjacent neighbors. When newly discovered neighbors are learned the address, interface, and Hold Time of the neighbor is noted. When a neighbor sends a HELLO, it advertises its Hold Time. The Hold Time is the amount of time a router treats a neighbor as reachable and operational. In addition to the HELLO packet, if any packet is received within the Hold Time period, then the Hold Time period will be reset. When the Hold Time expires, DUAL is informed of the topology change. Savage, et al. Informational [Page 32] RFC 7868 Cisco's EIGRP May 2016 5.3.2. HELLO Packets When an EIGRP router is initialized, it will start sending HELLO packets out any interface on which EIGRP is enabled. HELLO packets, when used for neighbor discovery, are normally sent multicast addressed. The HELLO packet will include the configured EIGRP metric K-values. Two routers become neighbors only if the K-values are the same. This enforces that the metric usage is consistent throughout the Internet. Also included in the HELLO packet is a Hold Time value. This value indicates to all receivers the length of time in seconds that the neighbor is valid. The default Hold Time will be three times the HELLO interval. HELLO packets will be transmitted every 5 seconds (by default). There may be a configuration command that controls this value and therefore changes the Hold Time. HELLO packets are not transmitted reliably, so the sequence number should be set to 0. 5.3.3. UPDATE Packets A router detects a new neighbor by receiving a HELLO packet from a neighbor not presently known. To ensure unicast and multicast packet delivery, the detecting neighbor will send a unicast UPDATE packet to the new neighbor with no routing information (the NULL UPDATE packet). The initial NULL UPDATE packet sent MUST have the INIT-Flag set and contain no topology information. Implementation note: The NULL UPDATE packet is used to ensure bidirectional UNICAST packet delivery as the NULL UPDATE and the ACK are both sent unicast. Additional UPDATE packets cannot be sent until the initial NULL UPDATE packet is acknowledged. The INIT-Flag instructs the neighbor to advertise its routes, and it is also useful when a neighbor goes down and comes back up before the router detects it went down. In this case, the neighbor needs new routing information. The INIT-Flag informs the router to send it. Implementation note: When a router sends an UPDATE with the INIT-Flag set, and without the Restart (RS) flag set in the header, the receiving neighbor must also send an UPDATE with the INIT-Flag. Failure to do so will result in a Cisco device posting a "stuck in INIT state" error and subsequent discards. Savage, et al. Informational [Page 33] RFC 7868 Cisco's EIGRP May 2016 5.3.4. Initialization Sequence Router A Router B (just booted) (up and running) (1)----------------> HELLO (multicast) <---------------- (2) SEQ=0, ACK=0 HELLO (multicast) SEQ=0, ACK=0 <---------------- (3) UPDATE (unicast) SEQ=10, ACK=0, INIT (4)----------------> UPDATE 11 is queued UPDATE (unicast) SEQ=100, ACK=10, INIT <---------------- (5) UPDATE (unicast) SEQ=11, ACK=100 All UPDATES sent (6)--------------/lost/-> ACK (unicast) SEQ=0, ACK=11 (5 seconds later) <---------------- (7) Duplicate received, UPDATE (unicast) packet discarded SEQ=11, ACK=100 (8)---------------> ACK (unicast) SEQ=0, ACK=11 Figure 9: Initialization Sequence (1) Router A sends a multicast HELLO and Router B discovers it. (2) Router B sends an expedited HELLO and starts the process of sending its topology table to Router A. In addition, Router B sends the NULL UPDATE packet with the INIT-Flag. The second packet is queued, but it cannot be sent until the first is acknowledged. (3) Router A receives the first UPDATE packet and processes it as a DUAL event. If the UPDATE contains topology information, the packet will be processed and stored in a topology table. Router B sends its first and only UPDATE packet with an accompanied ACK. Savage, et al. Informational [Page 34] RFC 7868 Cisco's EIGRP May 2016 (4) Router B receives UPDATE packet 100 from Router A. Router B can dequeue packet 10 from A's transmission list since the UPDATE acknowledged 10. It can now send UPDATE packet 11 and with an acknowledgment of Router A's UPDATE. (5) Router A receives the last UPDATE packet from Router B and acknowledges it. The acknowledgment gets lost. (6) Router B later retransmits the UPDATE packet to Router A. (7) Router A detects the duplicate and simply acknowledges the packet. Router B dequeues packet 11 from A's transmission list, and both routers are up and synchronized. 5.3.5. Neighbor Formation To prevent packets from being sent to a neighbor prior to verifying multicast and unicast packet delivery is reliable, a three-way handshake is utilized. During normal adjacency formation, multicast HELLOs cause the EIGRP process to place new neighbors into the neighbor table. Unicast packets are then used to exchange known routing information and complete the neighbor relationship (Section 5.2). To prevent EIGRP from sending sequenced packets to neighbors that fail to have bidirectional unicast/multicast, or one neighbor restarts while building the relationship, EIGRP MUST place the newly discovered neighbor in a "pending" state as follows: when Router A receives the first multicast HELLO from Router B, it places Router B in the pending state and transmits a unicast UPDATE containing no topology information and SHALL set the initialization bit. While Router B is in this state, A will send it neither a QUERY nor an UPDATE. When Router A receives the unicast acknowledgment from Router B, it will change the state from "pending" to "up". 5.3.6. QUERY Packets during Neighbor Formation As described above, during the initial formation of the neighbor relationship, EIGRP uses a form of three-way handshake to verify both unicast and multicast connectivity are working successfully. During this period of neighbor creation, the new neighbor is considered to be in the pending state, and it is not eligible to be included in the convergence process. Savage, et al. Informational [Page 35] RFC 7868 Cisco's EIGRP May 2016 Because of this, any QUERY received by an EIGRP router would not cause a QUERY to be sent to the new (and pending) neighbor. It would perform the DUAL process without the new peer in the conversation. To do this, when a router in the process of establishing a new neighbor receives a QUERY from a fully established neighbor, it performs the normal DUAL Feasible Successor check to determine whether it needs to REPLY with a valid path or whether it needs to enter the ACTIVE process on the prefix. If it determines that it must go active, each fully established neighbor that participates in the convergence process will be sent a QUERY packet, and REPLY packets are expected from each. Any pending neighbor will not be expected to REPLY and will not be sent a QUERY directly. If it resides on an interface containing a mix of fully established neighbors and pending neighbors, it might receive the QUERY, but it will not be expected to REPLY to it. 5.4. Topology Table The topology table is populated by the Protocol-Dependent Modules (PDMs) (IPv4/IPv6), and it is acted upon by the DUAL finite state machine. Associated with each entry are the destination address, a list of neighbors that have advertised this destination, and the metric associated with the destination. The metric is referred to as the "CD". The CD is the best-advertised RD from all neighbors, plus the link cost between the receiving router and the neighbor. The "RD" is the CD as advertised by the Feasible Successor for the destination. In other words, the Computed Distance, when sent by a neighbor, is referred to as the "Reported Distance" and is the metric that the neighboring router uses to reach the destination (its CD as described above). If the router is advertising a destination route, it MUST be using the route to forward packets; this is an important rule that distance vector protocols MUST follow. 5.4.1. Route Management Within the topology table, EIGRP has the notion of internal and external routes. Internal routes MUST be preferred over external routes, independent of the metric. In practical terms, if an internal route is received, the diffusing computation will be run considering only the internal routes. Only when no internal routes for a given destination exist will EIGRP choose the successor from the available external routes. Savage, et al. Informational [Page 36] RFC 7868 Cisco's EIGRP May 2016 5.4.1.1. Internal Routes Internal routes are destinations that have been originated within the same EIGRP AS. Therefore, a directly attached network that is configured to run EIGRP is considered an internal route and is propagated with this information throughout the network topology. Internal routes are tagged with the following information: o Router ID of the EIGRP router that originated the route. o Configurable administrator tag. 5.4.1.2. External Routes External routes are destinations that have been learned from another source, such as a different routing protocol or static route. These routes are marked individually with the identity of their origination. External routes are tagged with the following information: o Router ID of the EIGRP router that redistributed the route. o AS number where the destination resides. o Configurable administrator tag. o Protocol ID of the external protocol. o Metric from the external protocol. o Bit flags for default routing. As an example, suppose there is an AS with three border routers: BR1, BR2, and BR3. A border router is one that runs more than one routing protocol. The AS uses EIGRP as the routing protocol. Two of the border routers, BR1 and BR2, also use Open Shortest Path First (OSPF) [10] and the other, BR3, also uses the Routing Information Protocol (RIP). Routes learned by one of the OSPF border routers, BR1, can be conditionally redistributed into EIGRP. This means that EIGRP running in BR1 advertises the OSPF routes within its own AS. When it does so, it advertises the route and tags it as an OSPF-learned route with a metric equal to the routing table metric of the OSPF route. The router-id is set to BR1. The EIGRP route propagates to the other border routers. Let's say that BR3, the RIP border router, also advertises the same destinations as BR1. Therefore, BR3, redistributes the RIP routes into the EIGRP AS. BR2, then, has enough information to determine the AS entry point for the route, the original routing protocol used, and the metric. Savage, et al. Informational [Page 37] RFC 7868 Cisco's EIGRP May 2016 Further, the network administrator could assign tag values to specific destinations when redistributing the route. BR2 can utilize any of this information to use the route or re-advertise it back out into OSPF. Using EIGRP route tagging can give a network administrator flexible policy controls and help customize routing. Route tagging is particularly useful in transit ASes where EIGRP would typically interact with an inter-domain routing protocol that implements global policies. 5.4.2. Split Horizon and Poison Reverse In some circumstances, EIGRP will suppress or poison QUERY and UPDATE information to prevent routing loops as changes propagate though the network. Within Cisco, the split horizon rule suggests: "Never advertise a route out of the interface through which it was learned". EIGRP implements this to mean, "if you have a successor route to a destination, never advertise the route out the interface on which it was learned". The poison reverse rule states: "A route learned through an interface will be advertised as unreachable through that same interface". As with the case of split horizon, EIGRP applies this rule only to interfaces it is using for reaching the destination. Routes learned though interfaces that EIGRP is NOT using to reach the destination may have the route advertised out those interfaces. In EIGRP, split horizon suppresses a QUERY, where as poison reverse advertises a destination as unreachable. This can occur for a destination under any of the following conditions: o two routers are in startup or restart mode o advertising a topology table change o sending a query 5.4.2.1. Startup Mode When two routers first become neighbors, they exchange topology tables during startup mode. For each destination a router receives during startup mode, it advertises the same destination back to its new neighbor with a maximum metric (Poison Route). Savage, et al. Informational [Page 38] RFC 7868 Cisco's EIGRP May 2016 5.4.2.2. Advertising Topology Table Change If a router uses a neighbor as the successor for a given destination, it will send an UPDATE for the destination with a metric of infinity. 5.4.2.3. Sending a QUERY/UPDATE In most cases, EIGRP follows normal split-horizon rules. When a metric change is received from the successor via QUERY or UPDATE that causes the route to go ACTIVE, the router will send a QUERY to neighbors on all interfaces except the interface toward the successor. In other words, the router does not send the QUERY out of the inbound interface through which the information causing the route to go ACTIVE was received. An exception to this can occur if a router receives a QUERY from its successor while already reacting to an event that did not cause it to go ACTIVE, for example, a metric change from the successor that did not cause an ACTIVE transition, but was followed by the UPDATE/QUERY that does result the router to transition to ACTIVE. 5.5. EIGRP Metric Coefficients EIGRP allows for modification of the default composite metric calculation (see Section 5.6) through the use of coefficients (K- values). This adjustment allows for per-deployment tuning of network behavior. Setting K-values up to 254 scales the impact of the scalar metric on the final composite metric. EIGRP default coefficients have been carefully selected to provide optimal performance in most networks. The default K-values are as follows: K1 == K3 == 1 K2 == K4 == K5 == 0 K6 == 0 If K5 is equal to 0, then reliability quotient is defined to be 1. Savage, et al. Informational [Page 39] RFC 7868 Cisco's EIGRP May 2016 5.5.1. Coefficients K1 and K2 K1 is used to allow path selection to be based on the bandwidth available along the path. EIGRP can use one of two variations of Throughput-based path selection. o Maximum Theoretical Bandwidth: paths chosen based on the highest reported bandwidth o Network Throughput: paths chosen based on the highest "available" bandwidth adjusted by congestion-based effects (interface reported load) By default, EIGRP computes the Throughput using the maximum theoretical Throughput expressed in picoseconds per kilobyte of data sent. This inversion results in a larger number (more time) ultimately generating a worse metric. If K2 is used, the effect of congestion as a measure of load reported by the interface will be used to simulate the "available Throughput" by adjusting the maximum Throughput. 5.5.2. Coefficient K3 K3 is used to allow delay or latency-based path selection. Latency and delay are similar terms that refer to the amount of time it takes a bit to be transmitted to an adjacent neighbor. EIGRP uses one-way- based values either provided by the interface or computed as a factor of the link s bandwidth. 5.5.3. Coefficients K4 and K5 K4 and K5 are used to allow for path selection based on link quality and packet loss. Packet loss caused by network problems results in highly noticeable performance issues or Jitter with streaming technologies, voice over IP, online gaming and videoconferencing, and will affect all other network applications to one degree or another. Critical services should pass with less than 1% packet loss. Lower priority packet types might pass with less than 5% and then 10% for the lowest of priority of services. The final metric can be weighted based on the reported link quality. The handling of K5 is conditional. If K5 is equal to 0, then reliability quotient is defined to be 1. Savage, et al. Informational [Page 40] RFC 7868 Cisco's EIGRP May 2016 5.5.4. Coefficient K6 K6 has been introduced with Wide Metric support and is used to allow for Extended Attributes, which can be used to reflect in a higher aggregate metric than those having lower energy usage. Currently there are two Extended Attributes, Jitter and energy, defined in the scope of this document. 5.5.4.1. Jitter Use of Jitter-based Path Selection results in a path calculation with the lowest reported Jitter. Jitter is reported as the interval between the longest and shortest packet delivery and is expressed in microseconds. Higher values result in a higher aggregate metric when compared to those having lower Jitter calculations. Jitter is measured in microseconds and is accumulated along the path, with each hop using an averaged 3-second period to smooth out the metric change rate. Presently, EIGRP does not have the ability to measure Jitter, and, as such, the default value will be zero (0). Performance-based solutions such as PfR could be used to populate this field. 5.5.4.2. Energy Use of Energy-based Path Selection results in paths with the lowest energy usage being selected in a loop-free and deterministic manner. The amount of energy used is accumulative and has results in a higher aggregate metric than those having lower energy. Presently, EIGRP does not report energy usage, and as such the default value will be zero (0). 5.6. EIGRP Metric Calculations 5.6.1. Classic Metrics The composite metric is based on bandwidth, delay, load, and reliability. MTU is not an attribute for calculating the composite metric, but carried in the vector metrics. One of the original goals of EIGRP was to offer and enhance routing solutions for IGRP. To achieve this, EIGRP used the same composite metric as IGRP, with the terms multiplied by 256 to change the metric from 24 bits to 32 bits. Savage, et al. Informational [Page 41] RFC 7868 Cisco's EIGRP May 2016 5.6.1.1. Classic Composite Formulation EIGRP calculates the composite metric with the following formula: metric = 256 * ({(K1*BW) + [(K2*BW)/(256-LOAD)] + (K3*DELAY)} * (K5/(REL+K4))) In this formula, Bandwidth (BW) is the lowest interface bandwidth along the path, and delay (DELAY) is the sum of all outbound interface delays along the path. Load (LOAD) and reliability (REL) values are expressed percentages with a value of 1 to 255. Implementation note: Cisco IOS routers display reliability as a fraction of 255. That is, 255/255 is 100% reliability or a perfectly stable link; a value of 229/255 represents a 90% reliable link. Load is a value between 1 and 255. A load of 255/255 indicates a completely saturated link. A load of 127/255 represents a 50% saturated link. These values are not dynamically measured; they are only measured at the time a link changes. Bandwidth is the inverse minimum bandwidth (in kbps) of the path in bits per second scaled by a factor of 10^7. The formula for bandwidth is as follows: (10^7)/BWmin Implementation note: When converting the real bandwidth to the composite bandwidth, truncate before applying the scaling factor. When converting the composite bandwidth to the real bandwidth, apply the scaling factor before the division and only then truncate. The delay is the sum of the outgoing interface delay (in tens of microseconds) to the destination. A delay set to it maximum value (hexadecimal 0xFFFFFFFF) indicates that the network is unreachable. The formula for delay is as follows: [sum of delays] The default composite metric, adjusted for scaling factors, for EIGRP is: metric = 256 * { [(10^7)/ BWmin] + [sum of delays]} Minimum Bandwidth (BWmin) is represented in kbps, and the "sum of delays" is represented in tens of microseconds. The bandwidth and delay for an Ethernet interface are 10 Mbps and 1 ms, respectively. Savage, et al. Informational [Page 42] RFC 7868 Cisco's EIGRP May 2016 The calculated EIGRP bandwidth (BW) metric is then: 256 * (10^7)/BW = 256 * {(10^7)/10,000} = 256 * 1000 = 256,000 And the calculated EIGRP delay metric is then: 256 * sum of delay = 256 * 100 * 10 microseconds = 25,600 (in tens of microseconds) 5.6.1.2. Cisco Interface Delay Compatibility For compatibility with Cisco products, the following table shows the times in nanoseconds EIGRP uses for bandwidth and delay. Bandwidth Classic Wide Metrics Interface (kbps) Delay Delay Type --------------------------------------------------------- 9 500000000 500000000 Tunnel 56 20000000 20000000 56 kbps 64 20000000 20000000 DS0 1544 20000000 20000000 T1 2048 20000000 20000000 E1 10000 1000000 1000000 Ethernet 16000 630000 630000 TokRing16 45045 20000000 20000000 HSSI 100000 100000 100000 FDDI 100000 100000 100000 FastEthernet 155000 100000 100000 ATM 155 Mbps 1000000 10000 10000 GigaEthernet 2000000 10000 5000 2 Gig 5000000 10000 2000 5 Gig 10000000 10000 1000 10 Gig 20000000 10000 500 20 Gig 50000000 10000 200 50 Gig 100000000 10000 100 100 Gig 200000000 10000 50 200 Gig 500000000 10000 20 500 Gig 5.6.2. Wide Metrics To enable EIGRP to perform the path selection for interfaces with high bandwidths, both the EIGRP packet and composite metric formula have been modified. This change allows EIGRP to choose paths based on the computed time (measured in picoseconds) information takes to travel though the links. Savage, et al. Informational [Page 43] RFC 7868 Cisco's EIGRP May 2016 5.6.2.1. Wide Metric Vectors EIGRP uses five "vector metrics": minimum Throughput, latency, load, reliability, and MTU. These values are calculated from destination to source as follows: o Throughput - Minimum value o Latency - accumulative o Load - maximum o Reliability - minimum o MTU - minimum o Hop count - accumulative There are two additional values: Jitter and energy. These two values are accumulated from destination to source: o Jitter - accumulative o Energy - accumulative These Extended Attributes, as well as any future ones, will be controlled via K6. If K6 is non-zero, these will be additive to the path's composite metric. Higher Jitter or energy usage will result in paths that are worse than those that either do not monitor these attributes or that have lower values. EIGRP will not send these attributes if the router does not provide them. If the attributes are received, then EIGRP will use them in the metric calculation (based on K6) and will forward them with those routers values assumed to be "zero" and the accumulative values are forwarded unchanged. The use of the vector metrics allows EIGRP to compute paths based on any of four (bandwidth, delay, reliability, and load) path selection schemes. The schemes are distinguished based on the choice of the key-measured network performance metric. Of these vector metric components, by default, only minimum Throughput and latency are traditionally used to compute the best path. Unlike most metrics, minimum Throughput is set to the minimum value of the entire path, and it does not reflect how many hops or low Throughput links are in the path, nor does it reflect the availability of parallel links. Latency is calculated based on one- way delays and is a cumulative value, which increases with each segment in the path. Network Designer note: When trying to manually influence EIGRP path selection though interface bandwidth/delay configuration, the modification of bandwidth is discouraged for following reasons: Savage, et al. Informational [Page 44] RFC 7868 Cisco's EIGRP May 2016 The change will only affect the path selection if the configured value is the lowest bandwidth over the entire path. Changing the bandwidth can have impact beyond affecting the EIGRP metrics. For example, Quality of Service (QoS) also looks at the bandwidth on an interface. EIGRP throttles its packet transmissions so it will only use 50% of the configured bandwidth. Lowering the bandwidth can cause EIGRP to starve an adjacency, causing slow or failed convergence and control- plane operation. Changing the delay does not impact other protocols, nor does it cause EIGRP to throttle back; changing the delay configured on a link only impacts metric calculation. 5.6.2.2. Wide Metric Conversion Constants EIGRP uses a number of defined constants for conversion and calculation of metric values. These numbers are provided here for reference EIGRP_BANDWIDTH 10,000,000 EIGRP_DELAY_PICO 1,000,000 EIGRP_INACCESSIBLE 0xFFFFFFFFFFFFFFFFLL EIGRP_MAX_HOPS 100 EIGRP_CLASSIC_SCALE 256 EIGRP_WIDE_SCALE 65536 When computing the metric using the above units, all capacity information will be normalized to kilobytes and picoseconds before being used. For example, delay is expressed in microseconds per kilobyte, and would be converted to kilobytes per second; likewise, energy would be expressed in power per kilobytes per second of usage. 5.6.2.3. Throughput Calculation The formula for the conversion for Max-Throughput value directly from the interface without consideration of congestion-based effects is as follows: (EIGRP_BANDWIDTH * EIGRP_WIDE_SCALE) Max-Throughput = K1 * ------------------------------------ Interface Bandwidth (kbps) Savage, et al. Informational [Page 45] RFC 7868 Cisco's EIGRP May 2016 If K2 is used, the effect of congestion as a measure of load reported by the interface will be used to simulate the "available Throughput" by adjusting the maximum Throughput according to the formula: K2 * Max-Throughput Net-Throughput = Max-Throughput + --------------------- 256 - Load K2 has the greatest effect on the metric occurs when the load increases beyond 90%. 5.6.2.4. Latency Calculation Transmission times derived from physical interfaces MUST be n units of picoseconds, converted to picoseconds prior to being exchanged between neighbors, or used in the composite metric determination. This includes delay values present in configuration-based commands (i.e., interface delay, redistribute, default-metric, route-map, etc.). The delay value is then converted to a "latency" using the formula: Delay * EIGRP_WIDE_SCALE Latency = K3 * -------------------------- EIGRP_DELAY_PICO 5.6.2.5. Composite Calculation K5 metric =[(K1*Net-Throughput) + Latency)+(K6*ExtAttr)] * ------ K4+Rel By default, the path selection scheme used by EIGRP is a combination of Throughput and Latency where the selection is a product of total latency and minimum Throughput of all links along the path: metric = (K1 * min(Throughput)) + (K3 * sum(Latency)) } 6. EIGRP Packet Formats 6.1. Protocol Number The IPv6 and IPv4 protocol identifier number spaces are common and will both use protocol identifier 88 [8] [9]. Savage, et al. Informational [Page 46] RFC 7868 Cisco's EIGRP May 2016 EIGRP IPv4 will transmit HELLO packets using either the unicast destination of a neighbor or using a multicast host group address [7] with a source address EIGRP IPv4 multicast address [13]. EIGRP IPv6 will transmit HELLO packets with a source address being the link-local address of the transmitting interface. Multicast HELLO packets will have a destination address of EIGRP IPv6 multicast address [14]. Unicast packets directed to a specific neighbor will contain the destination link-local address of the neighbor. There is no requirement that two EIGRP IPv6 neighbors share a common prefix on their connecting interface. EIGRP IPv6 will check that a received HELLO contains a valid IPv6 link-local source address. Other HELLO processing will follow common EIGRP checks, including matching AS number and matching K-values. 6.2. Protocol Assignment Encoding The External Protocol field is an informational assignment to identify the originating routing protocol that this route was learned by. The following values are assigned: Protocols Value IGRP 1 EIGRP 2 Static 3 RIP 4 HELLO 5 OSPF 6 ISIS 7 EGP 8 BGP 9 IDRP 10 Connected 11 6.3. Destination Assignment Encoding Destinations types are encoded according to the IANA address family number assignments. Currently only the following types are used: AFI Description AFI Number -------------------------------------- IP (IP version 4) 1 IP6 (IP version 6) 2 EIGRP Common Service Family 16384 EIGRP IPv4 Service Family 16385 EIGRP IPv6 Service Family 16386 Savage, et al. Informational [Page 47] RFC 7868 Cisco's EIGRP May 2016 6.4. EIGRP Communities Attribute EIGRP supports communities similar to the BGP Extended Communities RFC 4360 [4] extended type with Type field composed of 2 octets and Value field composed of 6 octets. Each Community is encoded as an 8-octet quantity, as follows: - Type field: 2 octets - Value field: Remaining octets 0 1 2 3 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ | Type high | Type low | | +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ Value | | | +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ In addition to well-known communities supported by BGP (such as Site of Origin), EIGRP defines a number of additional Community values in the "Experimental Use" [5] range as follows: Type high: 0x88 Type low: Value Name Description --------------------------------------------------------------- 00 EXTCOMM_EIGRP EIGRP route information appended 01 EXTCOMM_DAD Data: AS + Delay 02 EXTCOMM_VRHB Vector: Reliability + Hop + BW 03 EXTCOMM_SRLM System: Reserve + Load + MTU 04 EXTCOMM_SAR System: Remote AS + Remote ID 05 EXTCOMM_RPM Remote: Protocol + Metric 06 EXTCOMM_VRR Vecmet: Rsvd + RouterID Savage, et al. Informational [Page 48] RFC 7868 Cisco's EIGRP May 2016 6.5. EIGRP Packet Header The basic EIGRP packet payload format is identical for both IPv4 and IPv6, although there are some protocol-specific variations. Packets consist of a header, followed by a set of variable-length fields consisting of Type/Length/Value (TLV) triplets. 0 1 2 3 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ |Header Version | Opcode | Checksum | +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ | Flags | +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ | Sequence Number | +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ | Acknowledgment Number | +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ | Virtual Router ID | Autonomous System Number | +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ Header Version: EIGRP Packet Header Format version. Current Version is 2. This field is not the same as the TLV Version field. Opcode: Indicates the type of the message. It will be one of the following values: EIGRP_OPC_UPDATE 1 EIGRP_OPC_REQUEST 2 EIGRP_OPC_QUERY 3 EIGRP_OPC_REPLY 4 EIGRP_OPC_HELLO 5 Reserved 6 (EIGRP_OPC_IPXSAP) Reserved 7 (EIGRP_OPC_PROBE) Reserved 8 (EIGRP_OPC_ACK) Reserved 9 EIGRP_OPC_SIAQUERY 10 EIGRP_OPC_SIAREPLY 11 Checksum: Each packet will include a checksum for the entire contents of the packet. The checksum will be the standard ones' complement of the ones' complement sum. For purposes of computing the checksum, the value of the checksum field is zero. The packet is discarded if the packet checksum fails. Flags: Defines special handling of the packet. There are currently four defined flag bits. Savage, et al. Informational [Page 49] RFC 7868 Cisco's EIGRP May 2016 INIT-Flag (0x01): This bit is set in the initial UPDATE sent to a newly discovered neighbor. It instructs the neighbor to advertise its full set of routes. CR-Flag (0x02): This bit indicates that receivers should only accept the packet if they are in Conditionally Received mode. A router enters Conditionally Received mode when it receives and processes a HELLO packet with a SEQUENCE TLV present. RS-Flag (0x04): The Restart flag is set in the HELLO and the UPDATE packets during the restart period. The router looks at the RS- Flag to detect if a neighbor is restarting. From the restarting routers perspective, if a neighboring router detects the RS-Flag set, it will maintain the adjacency, and will set the RS-Flag in its UPDATE packet to indicated it is doing a soft restart. EOT-Flag (0x08): The End-of-Table flag marks the end of the startup process with a neighbor. If the flag is set, it indicates the neighbor has completed sending all UPDATEs. At this point, the router will remove any stale routes learned from the neighbor prior to the restart event. A stale route is any route that existed before the restart and was not refreshed by the neighbor via and UPDATE. Sequence Number: Each packet that is transmitted will have a 32-bit sequence number that is unique with respect to a sending router. A value of 0 means that an acknowledgment is not required. Acknowledgment Number: The 32-bit sequence number that is being acknowledged with respect to the receiver of the packet. If the value is 0, there is no acknowledgment present. A non-zero value can only be present in unicast-addressed packets. A HELLO packet with a non-zero ACK field should be decoded as an ACK packet rather than a HELLO packet. Virtual Router Identifier (VRID): A 16-bit number that identifies the virtual router with which this packet is associated. Packets received with an unknown, or unsupported, value will be discarded. Value Range Usage 0x0000 Unicast Address Family 0x0001 Multicast Address Family 0x0002-0x7FFF Reserved 0x8000 Unicast Service Family 0x8001-0xFFFF Reserved Savage, et al. Informational [Page 50] RFC 7868 Cisco's EIGRP May 2016 Autonomous System Number: 16-bit unsigned number of the sending system. This field is indirectly used as an authentication value. That is, a router that receives and accepts a packet from a neighbor must have the same AS number or the packet is ignored. The range of valid AS numbers is 1 through 65,535. 6.6. EIGRP TLV Encoding Format The contents of each packet can contain a variable number of fields. Each field will be tagged and include a length field. This allows for newer versions of software to add capabilities and coexist with old versions of software in the same configuration. Fields that are tagged and not recognized can be skipped over. Another advantage of this encoding scheme is that it allows multiple network-layer protocols to carry independent information. Therefore, if it is later decided to implement a single "integrated" protocol, this can be done. The format of a {type, length, value} (TLV) is encoded as follows: 0 1 2 3 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ | Type high | Type low | Length | +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ | Value (variable length) | +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ The type values are the ones defined below. The length value specifies the length in octets of the type, length, and value fields. TLVs can appear in a packet in any order, and there are no interdependencies among them. Malformed TLVs contained in EIGRP messages are handled by silently discarding the containing message. A TLV is malformed if the TLV Length is invalid or if the TLV extends beyond the end of the containing message. Savage, et al. Informational [Page 51] RFC 7868 Cisco's EIGRP May 2016 6.6.1. Type Field Encoding The type field is structured as follows: Type High: 1 octet that defines the protocol classification: Protocol ID VERSION General 0x00 1.2 IPv4 0x01 1.2 IPv6 0x04 1.2 SAF 0x05 3.0 Multiprotocol 0x06 2.0 Type Low: 1 octet that defines the TLV Opcode; see TLV Definitions in Section 3. 6.6.2. Length Field Encoding The Length field is a 2-octet unsigned number, which indicates the length of the TLV. The value includes the Type and Length fields. 6.6.3. Value Field Encoding The Value field is a multi-octet field containing the payload for the TLV. 6.7. EIGRP Generic TLV Definitions Ver 1.2 Ver 2.0 PARAMETER_TYPE 0x0001 0x0001 AUTHENTICATION_TYPE 0x0002 0x0002 SEQUENCE_TYPE 0x0003 0x0003 SOFTWARE_VERSION_TYPE 0x0004 0x0004 MULTICAST_SEQUENCE_TYPE 0x0005 0x0005 PEER_INFORMATION_TYPE 0x0006 0x0006 PEER_TERMINATION_TYPE 0x0007 0x0007 PEER_TID_LIST_TYPE --- 0x0008 Savage, et al. Informational [Page 52] RFC 7868 Cisco's EIGRP May 2016 6.7.1. 0x0001 - PARAMETER_TYPE This TLV is used in HELLO packets to convey the EIGRP metric coefficient values: noted as "K-values" as well as the Hold Time values. This TLV is also used in an initial UPDATE packet when a neighbor is discovered. 0 1 2 3 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ | 0x0001 | 0x000C | +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ | K1 | K2 | K3 | K4 | +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ | K5 | K6 | Hold Time | +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ K-values: The K-values associated with the EIGRP composite metric equation. The default values for weights are: K1 - 1 K2 - 0 K3 - 1 K4 - 0 K5 - 0 K6 - 0 Hold Time: The amount of time in seconds that a receiving router should consider the sending neighbor valid. A valid neighbor is one that is able to forward packets and participates in EIGRP. A router that considers a neighbor valid will store all routing information advertised by the neighbor. 6.7.2. 0x0002 - AUTHENTICATION_TYPE This TLV may be used in any EIGRP packet and conveys the authentication type and data used. Routers receiving a mismatch in authentication shall discard the packet. 0 1 2 3 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ | 0x0002 | Length | +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ | Auth Type | Auth Length | Auth Data (Variable) | +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ Savage, et al. Informational [Page 53] RFC 7868 Cisco's EIGRP May 2016 Authentication Type: The type of authentication used. Authentication Length: The length, measured in octets, of the individual authentication. Authentication Data: Variable-length field reflected by "Auth Length", which is dependent on the type of authentication used. Multiple authentication types can be present in a single AUTHENTICATION_TYPE TLV. 6.7.2.1. 0x02 - MD5 Authentication Type MD5 Authentication will use Auth Type code 0x02, and the Auth Data will be the MD5 Hash value. 6.7.2.2. 0x03 - SHA2 Authentication Type SHA2-256 Authentication will use Type code 0x03, and the Auth Data will be the 256-bit SHA2 [6] Hash value. 6.7.3. 0x0003 - SEQUENCE_TYPE This TLV is used for a sender to tell receivers to not accept packets with the CR-Flag set. This is used to order multicast and unicast addressed packets. 0 1 2 3 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ | 0x0003 | Length | +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ |Address Length | Protocol Address | +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ The Address Length and Protocol Address will be repeated one or more times based on the Length field. Address Length: Number of octets for the address that follows. For IPv4, the value is 4. For IPv6, it is 16. For AppleTalk, the value is 4; for Novell IPX, the value is 10 (both are no longer in use). Protocol Address: Neighbor address on interface in which the HELLO with SEQUENCE TLV is sent. Each address listed in the HELLO packet is a neighbor that should not enter Conditionally Received mode. Savage, et al. Informational [Page 54] RFC 7868 Cisco's EIGRP May 2016 6.7.4. 0x0004 - SOFTWARE_VERSION_TYPE Field Length Vender OS major version 1 Vender OS minor version 1 EIGRP major revision 1 EIGRP minor revision 1 The EIGRP TLV Version fields are used to determine TLV format versions. Routers using Version 1.2 TLVs do not understand Version 2.0 TLVs, therefore Version 2.0 routers must send the packet with both TLV formats in a mixed network. 0 1 2 3 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ | 0x0004 | 0x000C | +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ |Vendor Major V.|Vendor Minor V.| EIGRP Major V.| EIGRP Minor V.| +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ 6.7.5. 0x0005 - MULTICAST_SEQUENCE_TYPE The next multicast SEQUENCE TLV. 0 1 2 3 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ | 0x0005 | 0x0008 | +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ | Sequence Number | +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ 6.7.6. 0x0006 - PEER_INFORMATION_TYPE This TLV is reserved, and not part of this document. Savage, et al. Informational [Page 55] RFC 7868 Cisco's EIGRP May 2016 6.7.7. 0x0007 - PEER_ TERMINATION_TYPE This TLV is used in HELLO packets to notify the list of neighbor(s) the router has reset the adjacency. This TLV is used in HELLO packets to notify the list of neighbors that the router has reset the adjacency. This is used anytime a router needs to reset an adjacency, or signal an adjacency it is going down. 0 1 2 3 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ | 0x0007 | Length | +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ | Address List (variable) | +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ Implementation note: Older Cisco routers implement this using the "Parameters TLV" with all K-values set to 255 (except K6). 6.7.8. 0x0008 - TID_LIST_TYPE List of sub-topology identifiers, including the Base Topology, supported by the router. 0 1 2 3 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ | 0x0008 | Length | +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ | Topology Identification List (variable) | +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ If this information changes from the last state, it means either a new topology was added or an existing topology was removed. This TLV is ignored until the three-way handshake has finished When the TID list is received, it compares the list to the previous list sent. If a TID is found that does not previously exist, the TID is added to the neighbor's topology list, and the existing sub- topology is sent to the peer. If a TID that was in a previous list is not found, the TID is removed from the neighbor's topology list and all routes learned though that neighbor for that sub-topology are removed from the topology table. Savage, et al. Informational [Page 56] RFC 7868 Cisco's EIGRP May 2016 6.8. Classic Route Information TLV Types 6.8.1. Classic Flag Field Encoding EIGRP transports a number of flags with in the TLVs to indicate addition route state information. These bits are defined as follows: Flags Field ----------- Source Withdraw (Bit 0) - Indicates if the router that is the original source of the destination is withdrawing the route from the network or if the destination is lost due as a result of a network failure. Candidate Default (CD) (Bit 1) - Set to indicate the destination should be regarded as a candidate for the default route. An EIGRP default route is selected from all the advertised candidate default routes with the smallest metric. ACTIVE (Bit 2) - Indicates if the route is in the ACTIVE State. 6.8.2. Classic Metric Encoding The handling of bandwidth and delay for Classic TLVs is encoded in the packet "scaled" form relative to how they are represented on the physical link. 0 1 2 3 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ | Scaled Delay | +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ | Scaled Bandwidth | +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ | MTU | Hop Count | +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ | Reliability | Load | Internal Tag | Flags Field | +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ Scaled Delay: An administrative parameter assigned statically on a per-interface-type basis to represent the time it takes along an unloaded path. This is expressed in units of tens of microseconds divvied by 256. A delay of 0xFFFFFFFF indicates an unreachable route. Scaled Bandwidth: The path bandwidth measured in bits per second. In units of 2,560,000,000/kbps. Savage, et al. Informational [Page 57] RFC 7868 Cisco's EIGRP May 2016 MTU: The minimum MTU size for the path to the destination. Hop Count: The number of router traversals to the destination. Reliability: The current error rate for the path, measured as an error percentage. A value of 255 indicates 100% reliability Load: The load utilization of the path to the destination, measured as a percentage. A value of 255 indicates 100% load. Internal-Tag: A tag assigned by the network administrator that is untouched by EIGRP. This allows a network administrator to filter routes in other EIGRP border routers based on this value. Flags Field: See Section 6.8.1. 6.8.3. Classic Exterior Encoding Additional routing information so provided for destinations outside of the EIGRP AS as follows: 0 1 2 3 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ | Router Identifier (RID) | +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ | External Autonomous System (AS) Number | +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ | Administrative Tag | +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ | External Protocol Metric | +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ | Reserved |Extern Protocol| Flags Field | +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ Router Identifier (RID): A 32-bit number provided by the router sourcing the information to uniquely identify it as the source. External Autonomous System (AS) Number: A 32-bit number indicating the external AS of which the sending router is a member. If the source protocol is EIGRP, this field will be the [VRID, AS] pair. If the external protocol does not have an AS, other information can be used (for example, Cisco uses process-id for OSPF). Administrative Tag: A tag assigned by the network administrator that is untouched by EIGRP. This allows a network administrator to filter routes in other EIGRP border routers based on this value. Savage, et al. Informational [Page 58] RFC 7868 Cisco's EIGRP May 2016 External Protocol Metric: 32-bit value of the composite metric that resides in the routing table as learned by the foreign protocol. If the External Protocol is IGRP or another EIGRP routing process, the value can optionally be the composite metric or 0, and the metric information is stored in the metric section. External Protocol: Contains an enumerated value defined in Section 6.2 to identify the routing protocol (external protocol) redistributing the route. Flags Field: See Section 6.8.1 6.8.4. Classic Destination Encoding EIGRP carries destination in a compressed form, where the number of bits significant in the variable-length address field are indicated in a counter. 0 1 2 3 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ | Subnet Mask | Destination Address (variable length) | | Bit Count | ((Bit Count - 1) / 8) + 1 | +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ Subnet Mask Bit Count: 8-bit value used to indicate the number of bits in the subnet mask. A value of 0 indicates the default network, and no address is present. Destination Address: A variable-length field used to carry the destination address. The length is determined by the number of consecutive bits in the destination address. The formula to calculate the length is address-family dependent: IPv4: ((Bit Count - 1) / 8) + 1 IPv6: (Bit Count == 128) ? 16 : ((x / 8) + 1) 6.8.5. IPv4-Specific TLVs INTERNAL_TYPE 0x0102 EXTERNAL_TYPE 0x0103 COMMUNITY_TYPE 0x0104 Savage, et al. Informational [Page 59] RFC 7868 Cisco's EIGRP May 2016 6.8.5.1. IPv4 INTERNAL_TYPE This TLV conveys IPv4 destination and associated metric information for IPv4 networks. Routes advertised in this TLV are network interfaces that EIGRP is configured on as well as networks that are learned via other routers running EIGRP. 0 1 2 3 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ | 0x01 | 0x02 | Length | +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ | Next-Hop Forwarding Address | +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ | Vector Metric Section (see Section 6.8.2) | +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-| | Destination Section | | IPv4 Address (variable length) | | (see Section 6.8.4) | +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ Next-Hop Forwarding Address: IPv4 address represented by four 8-bit values (total 4 octets). If the value is zero (0), the IPv4 address from the received IPv4 header is used as the next hop for the route. Otherwise, the specified IPv4 address will be used. Vector Metric Section: The vector metrics for destinations contained in this TLV. See the description of "metric encoding" in Section 6.8.2. Destination Section: The network/subnet/host destination address being requested. See the description of "destination" in Section 6.8.4. 6.8.5.2. IPv4 EXTERNAL_TYPE This TLV conveys IPv4 destination and metric information for routes learned by other routing protocols that EIGRP injects into the AS. Available with this information is the identity of the routing protocol that created the route, the external metric, the AS number, an indicator if it should be marked as part of the EIGRP AS, and a network-administrator tag used for route filtering at EIGRP AS boundaries. Savage, et al. Informational [Page 60] RFC 7868 Cisco's EIGRP May 2016 0 1 2 3 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ | 0x01 | 0x03 | Length | +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ | Next-Hop Forwarding Address | +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ | Exterior Section (see Section 6.8.3) | +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ | Vector Metric Section (see Section 6.8.2) | +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-| | Destination Section | | IPv4 Address (variable length) | | (see Section 6.8.4) | +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ Next-Hop Forwarding Address: IPv4 address represented by four 8-bit values (total 4 octets). If the value is zero (0), the IPv4 address from the received IPv4 header is used as the next hop for the route. Otherwise, the specified IPv4 address will be used. Exterior Section: Additional routing information provided for a destination that is outside of the AS and that has been redistributed into the EIGRP. See the description of "exterior encoding" in Section 6.8.3. Vector Metric Section: Vector metrics for destinations contained in this TLV. See the description of "metric encoding" in Section 6.8.2. Destination Section: The network/subnet/host destination address being requested. See the description of "destination" in Section 6.8.4. Savage, et al. Informational [Page 61] RFC 7868 Cisco's EIGRP May 2016 6.8.5.3. IPv4 COMMUNITY_TYPE This TLV is used to provide community tags for specific IPv4 destinations. 0 1 2 3 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ | 0x01 | 0x04 | Length | +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ | IPv4 Destination | +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ | Reserved | Community Length | +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ | Community List | | (variable length) | +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ IPv4 Destination: The IPv4 address with which the community information should be stored. Community Length: A 2-octet unsigned number that indicates the length of the Community List. The length does not include the IPv4 Address, Reserved, or Length fields. Community List: One or more 8-octet EIGRP communities, as defined in Section 6.4. 6.8.6. IPv6-Specific TLVs INTERNAL_TYPE 0x0402 EXTERNAL_TYPE 0x0403 COMMUNITY_TYPE 0x0404 Savage, et al. Informational [Page 62] RFC 7868 Cisco's EIGRP May 2016 6.8.6.1. IPv6 INTERNAL_TYPE This TLV conveys the IPv6 destination and associated metric information for IPv6 networks. Routes advertised in this TLV are network interfaces that EIGRP is configured on as well as networks that are learned via other routers running EIGRP. 0 1 2 3 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ | 0x04 | 0x02 | Length | +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ | | | Next-Hop Forwarding Address | | (16 octets) | | | +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ | Vector Metric Section (see Section 6.8.2) | +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-| | Destination Section | | IPv6 Address (variable length) | | (see Section 6.8.4) | +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ Next-Hop Forwarding Address: This IPv6 address is represented by eight groups of 16-bit values (total 16 octets). If the value is zero (0), the IPv6 address from the received IPv6 header is used as the next hop for the route. Otherwise, the specified IPv6 address will be used. Vector Metric Section: Vector metrics for destinations contained in this TLV. See the description of "metric encoding" in Section 6.8.2. Destination Section: The network/subnet/host destination address being requested. See the description of "destination" in Section 6.8.4. 6.8.6.2. IPv6 EXTERNAL_TYPE This TLV conveys IPv6 destination and metric information for routes learned by other routing protocols that EIGRP injects into the topology. Available with this information is the identity of the routing protocol that created the route, the external metric, the AS number, an indicator if it should be marked as part of the EIGRP AS, and a network administrator tag used for route filtering at EIGRP AS boundaries. Savage, et al. Informational [Page 63] RFC 7868 Cisco's EIGRP May 2016 0 1 2 3 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ | 0x04 | 0x03 | Length | +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ | | | Next-Hop Forwarding Address | | (16 octets) | | | +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ | Exterior Section (see Section 6.8.3) | +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ | Vector Metric Section (see Section 6.8.2) | +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-| | Destination Section | | IPv6 Address (variable length) | | (see Section 6.8.4) | +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ Next-Hop Forwarding Address: IPv6 address is represented by eight groups of 16-bit values (total 16 octets). If the value is zero (0), the IPv6 address from the received IPv6 header is used as the next hop for the route. Otherwise, the specified IPv6 address will be used. Exterior Section: Additional routing information provided for a destination that is outside of the AS and that has been redistributed into the EIGRP. See the description of "exterior encoding" in Section 6.8.3. Vector Metric Section: vector metrics for destinations contained in this TLV. See the description of "metric encoding" in Section 6.8.2. Destination Section: The network/subnet/host destination address being requested. See the description of "destination" in Section 6.8.4. Savage, et al. Informational [Page 64] RFC 7868 Cisco's EIGRP May 2016 6.8.6.3 IPv6 COMMUNITY_TYPE This TLV is used to provide community tags for specific IPv4 destinations. 0 1 2 3 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ | 0x04 | 0x04 | Length | +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ | | | Destination | | (16 octets) | | | +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ | Reserved | Community Length | +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ | Community List | | (variable length) | +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ Destination: The IPv6 address with which the community information should be stored. Community Length: A 2-octet unsigned number that indicates the length of the Community List. The length does not include the IPv6 Address, Reserved, or Length fields. Community List: One or more 8-octet EIGRP communities, as defined in Section 6.4. Savage, et al. Informational [Page 65] RFC 7868 Cisco's EIGRP May 2016 6.9. Multiprotocol Route Information TLV Types This TLV conveys topology and associated metric information. 0 1 2 3 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ |Header Version | Opcode | Checksum | +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ | Flags | +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ | Sequence Number | +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ | Acknowledgment Number | +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ | Virtual Router ID | Autonomous System Number | +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ | TLV Header Encoding | | (see Section 6.9.1) | +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ | Wide Metric Encoding | | (see Section 6.9.2) | +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ | Destination Descriptor | | (variable length) | +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ 6.9.1. TLV Header Encoding There has been a long-standing requirement for EIGRP to support routing technologies, such as multi-topologies, and to provide the ability to carry destination information independent of the transport. To accomplish this, a Vector has been extended to have a new "Header Extension Header" section. This is a variable-length field and, at a minimum, it will support the following fields: 0 1 2 3 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ | Type High | Type Low | Length | +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ | AFI | TID | +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ | Router Identifier (RID) | +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ | Value (variable length) | +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ Savage, et al. Informational [Page 66] RFC 7868 Cisco's EIGRP May 2016 The available fields are: TYPE - Topology TLVs have the following TYPE codes: Type High: 0x06 Type Low: REQUEST_TYPE 0x01 INTERNAL_TYPE 0x02 EXTERNAL_TYPE 0x03 Router Identifier (RID): A 32-bit number provided by the router sourcing the information to uniquely identify it as the source. 6.9.2. Wide Metric Encoding Multiprotocol TLVs will provide an extendable section of metric information, which is not used for the primary routing compilation. Additional per-path information is included to enable per-path cost calculations in the future. Use of the per-path costing along with the VID/TID will prove a complete solution for multidimensional routing. 0 1 2 3 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ | Offset | Priority | Reliability | Load | +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ | MTU | Hop Count | +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ | Delay | | +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ | | | +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ | | Bandwidth | +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ | Reserved | Opaque Flags | +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ | Extended Attributes | | (variable length) | +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ The fields are as follows: Offset: Number of 16-bit words in the Extended Attribute section that are used to determine the start of the destination information. A value of zero indicates no Extended Attributes are attached. Savage, et al. Informational [Page 67] RFC 7868 Cisco's EIGRP May 2016 Priority: Priority of the prefix when processing a route. In an AS using priority values, a destination with a higher priority receives preferential treatment and is serviced before a destination with a lower priority. A value of zero indicates no priority is set. Reliability: The current error rate for the path. Measured as an error percentage. A value of 255 indicates 100% reliability Load: The load utilization of the path to the destination, measured as a percentage. A value of 255 indicates 100% load. MTU: The minimum MTU size for the path to the destination. Not used in metric calculation but available to underlying protocols Hop Count: The number of router traversals to the destination. Delay: The one-way latency along an unloaded path to the destination expressed in units of picoseconds per kilobit. This number is not scaled; a value of 0xFFFFFFFFFFFF indicates an unreachable route. Bandwidth: The path bandwidth measured in kilobit per second as presented by the interface. This number is not scaled; a value of 0xFFFFFFFFFFFF indicates an unreachable route. Reserved: Transmitted as 0x0000. Opaque Flags: 16-bit protocol-specific flags. Values currently defined by Cisco are: OPAQUE_SRCWD 0x01 Route Source Withdraw OPAQUE_CD 0x02 Candidate default route OPAQUE_ACTIVE 0x04 Route is currently in active state OPAQUE_REPL 0x08 Route is replicated from another VRF Extended Attributes (Optional): When present, defines extendable per- destination attributes. This field is not normally transmitted. 6.9.3. Extended Metrics Extended metrics allow for extensibility of the vector metrics in a manner similar to RFC 6390 [11]. Each Extended metric shall consist of a header identifying the type (Opcode) and the length (Offset) followed by application-specific information. Extended metric values not understood must be treated as opaque and passed along with the associated route. Savage, et al. Informational [Page 68] RFC 7868 Cisco's EIGRP May 2016 The general formats for the Extended Metric fields are: 0 1 2 3 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ | Opcode | Offset | Data | +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ Opcode: Indicates the type of Extended Metric. Offset: Number of 16-bit words in the application-specific information. Offset does not include the length of the Opcode or Offset. Data: Zero or more octets of data as defined by Opcode. 6.9.3.1. 0x00 - NoOp This is used to pad the attribute section to ensure 32-bit alignment of the metric encoding section. 0 1 2 3 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ | 0x00 | 0x00 | +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ The fields are: Opcode: Transmitted as zero (0). Offset: Transmitted as zero (0) indicating no data is present. Data: No data is present with this attribute. Savage, et al. Informational [Page 69] RFC 7868 Cisco's EIGRP May 2016 6.9.3.2. 0x01 - Scaled Metric If a route is received from a back-rev neighbor, and the route is selected as the best path, the scaled metric received in the older UPDATE may be attached to the packet. If received, the value is for informational purposes and is not affected by K6. 0 1 2 3 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ | 0x01 | 0x04 | Reserved | +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ | Scaled Bandwidth | +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ | Scaled Delay | +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ Reserved: Transmitted as 0x0000 Scaled Bandwidth: The minimum bandwidth along a path expressed in units of 2,560,000,000/kbps. A bandwidth of 0xFFFFFFFF indicates an unreachable route. Scaled Delay: An administrative parameter assigned statically on a per-interface-type basis to represent the time it takes along an unloaded path. This is expressed in units of tens of microseconds divvied by 256. A delay of 0xFFFFFFFF indicates an unreachable route. 6.9.3.3. 0x02 - Administrator Tag EIGRP administrative tag does not alter the path decision-making process. Routers can set a tag value on a route and use the flags to apply specific routing polices within their network. 0 1 2 3 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ | 0x02 | 0x02 | Administrator Tag | +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ | Administrator Tag (cont.) | +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ Administrator Tag: A tag assigned by the network administrator that is untouched by EIGRP. This allows a network administrator to filter routes in other EIGRP border routers based on this value. Savage, et al. Informational [Page 70] RFC 7868 Cisco's EIGRP May 2016 6.9.3.4. 0x03 - Community List EIGRP communities themselves do not alter the path decision-making process, communities can be used as flags in order to mark a set of routes. Upstream routers can then use these flags to apply specific routing polices within their network. 0 1 2 3 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ | 0x03 | Offset | Community List | +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ | | (variable length) | +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ Offset: Number of 16-bit words in the sub-field. Community List: One or more 8-octet EIGRP communities, as defined in Section 6.4. 6.9.3.5. 0x04 - Jitter (Optional) EIGRP can carry one-way Jitter in networks that carry UDP traffic if the node is capable of measuring UDP Jitter. The Jitter reported to will be averaged with any existing Jitter data and include in the route updates. If no Jitter value is reported by the peer for a given destination, EIGRP will use the locally collected value. 0 1 2 3 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ | 0x04 | 0x03 | Jitter | +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ | | | +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ Jitter: The measure of the variability over time of the latency across a network measured in measured in microseconds. 6.9.3.6. 0x05 - Quiescent Energy (Optional) EIGRP can carry energy usage by nodes in networks if the node is capable of measuring energy. The Quiescent Energy reported will be added to any existing energy data and include in the route updates. If no energy data is reported by the peer for a given destination, EIGRP will use the locally collected value. Savage, et al. Informational [Page 71] RFC 7868 Cisco's EIGRP May 2016 0 1 2 3 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ | 0x05 | 0x02 | Q-Energy (high) | +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ | Q-Energy (low) | +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ Q-Energy: Paths with higher idle (standby) energy usage will be reflected in a higher aggregate metric than those having lower energy usage. If present, this number will represent the idle power consumption expressed in milliwatts per kilobit. 6.9.3.7. 0x06 - Energy (Optional) EIGRP can carry energy usage by nodes in networks if the node is capable of measuring energy. The active Energy reported will be added to any existing energy data and include in the route updates. If no energy data is reported by the peer for a given destination, EIGRP will use the locally collected value. 0 1 2 3 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ | 0x06 | 0x02 | Energy (high) | +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ | Energy (low) | +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ Energy: Paths with higher active energy usage will be reflected in a higher aggregate metric than those having lower energy usage. If present, this number will represent the power consumption expressed in milliwatts per kilobit. 6.9.3.8. 0x07 - AddPath The Add Path enables EIGRP to advertise multiple best paths to adjacencies. There will be up to a maximum of four AddPaths supported, where the format of the field will be as follows. 0 1 2 3 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ | 0x07 | Offset | AddPath (Variable Length) | +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ Offset: Number of 16-bit words in the sub-field. Savage, et al. Informational [Page 72] RFC 7868 Cisco's EIGRP May 2016 AddPath: Length of this field will vary in length based on whether it contains IPv4 or IPv6 data. 6.9.3.8.1. AddPath with IPv4 Next Hop 0 1 2 3 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ | 0x07 | Offset | Next-Hop Addr. (Upper 2 bytes)| +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ | IPv4 Address (Lower 2 bytes) | RID (Upper 2 bytes) | +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ | RID (Upper 2 bytes) | Admin Tag (Upper 2 bytes) | +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ | Admin Tag (Upper 2 bytes) |Extern Protocol| Flags Field | +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ Next-Hop Address: An IPv4 address represented by four 8-bit values (total 4 octets). If the value is zero (0), the IPv6 address from the received IPv4 header is used as the next hop for the route. Otherwise, the specified IPv4 address will be used. Router Identifier (RID): A 32-bit number provided by the router sourcing the information to uniquely identify it as the source. Admin Tag: A 32-bit administrative tag assigned by the network. This allows a network administrator to filter routes based on this value. If the route is of type external, then two additional bytes will be added as follows: External Protocol: Contains an enumerated value defined in Section 6.2 to identify the routing protocol (external protocol) redistributing the route. Flags Field: See Section 6.8.1. Savage, et al. Informational [Page 73] RFC 7868 Cisco's EIGRP May 2016 6.9.3.8.2. AddPath with IPv6 Next Hop 0 1 2 3 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ | 0x07 | Offset | Next-Hop Address | +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ | | | | (16 octets) | | +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-| | | RID (Upper 2 byes) | +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ | RID (Upper 2 byes) | Admin Tag (Upper 2 byes) | +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ | Admin Tag (Upper 2 byes) | Extern Protocol | Flags Field | +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ Next-Hop Address: An IPv6 address represented by eight groups of 16-bit values (total 16 octets). If the value is zero (0), the IPv6 address from the received IPv6 header is used as the next hop for the route. Otherwise, the specified IPv6 address will be used. Router Identifier (RID): A 32-bit number provided by the router sourcing the information to uniquely identify it as the source. Admin Tag: A 32-bit administrative tag assigned by the network. This allows a network administrator to filter routes based on this value. If the route is of type external, then two addition bytes will be added as follows: External Protocol: Contains an enumerated value defined in Section 6.2 to identify the routing protocol (external protocol) redistributing the route. Flags Field: See Section 6.8.1. Savage, et al. Informational [Page 74] RFC 7868 Cisco's EIGRP May 2016 6.9.4. Exterior Encoding Additional routing information provided for destinations outside of the EIGRP AS as follows: 0 1 2 3 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ | Router Identifier (RID) | +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ | External Autonomous System (AS) Number | +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ | External Protocol Metric | +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ | Reserved |Extern Protocol| Flags Field | +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ Router Identifier (RID): A 32-bit number provided by the router sourcing the information to uniquely identify it as the source. External Autonomous System (AS) Number: A 32-bit number indicating the external AS of which the sending router is a member. If the source protocol is EIGRP, this field will be the [VRID, AS] pair. If the external protocol does not have an AS, other information can be used (for example, Cisco uses process-id for OSPF). External Protocol Metric: A 32-bit value of the metric used by the routing table as learned by the foreign protocol. If the External Protocol is IGRP or EIGRP, the value can (optionally) be 0, and the metric information is stored in the metric section. External Protocol: Contains an enumerated value defined in Section 6.2 to identify the routing protocol (external protocol) redistributing the route. Flags Field: See Section 6.8.1. Savage, et al. Informational [Page 75] RFC 7868 Cisco's EIGRP May 2016 6.9.5. Destination Encoding Destination information is encoded in Multiprotocol packets in the same manner used by Classic TLVs. This is accomplished by using a counter to indicate how many significant bits are present in the variable-length address field. 0 1 2 3 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ | Subnet Mask | Destination Address (variable length | | Bit Count | ((Bit Count - 1) / 8) + 1 | +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ Subnet Mask Bit Count: 8-bit value used to indicate the number of bits in the subnet mask. A value of 0 indicates the default network and no address is present. Destination Address: A variable-length field used to carry the destination address. The length is determined by the number of consecutive bits in the destination address. The formula to calculate the length is address-family dependent: IPv4: ((Bit Count - 1) / 8) + 1 IPv6: (Bit Count == 128) ? 16 : ((x / 8) + 1) 6.9.6. Route Information 6.9.6.1. INTERNAL TYPE This TLV conveys destination information based on the IANA AFI defined in the TLV Header (see Section 6.9.1), and associated metric information. Routes advertised in this TLV are network interfaces that EIGRP is configured on as well as networks that are learned via other routers running EIGRP. 6.9.6.2. EXTERNAL TYPE This TLV conveys destination information based on the IANA AFI defined in the TLV Header (see Section 6.9.1), and metric information for routes learned by other routing protocols that EIGRP injects into the AS. Available with this information is the identity of the routing protocol that created the route, the external metric, the AS number, an indicator if it should be marked as part of the EIGRP AS, and a network administrator tag used for route filtering at EIGRP AS boundaries. Savage, et al. Informational [Page 76] RFC 7868 Cisco's EIGRP May 2016 7. Security Considerations Being promiscuous, EIGRP will neighbor with any router that sends a valid HELLO packet. Due to security considerations, this "completely" open aspect requires policy capabilities to limit peering to valid routers. EIGRP does not rely on a PKI or a heavyweight authentication system. These systems challenge the scalability of EIGRP, which was a primary design goal. Instead, Denial-of-Service (DoS) attack prevention will depend on implementations rate-limiting packets to the control plane as well as authentication of the neighbor through the use of MD5 or SHA2-256 [6]. 8. IANA Considerations This document serves as the sole reference for two multicast addresses: 224.0.0.10 for IPv4 "EIGRP Routers" [13] and FF02:0:0:0:0:0:0:A for IPv6 "EIGRP Routers" [14]. It also serves as assignment for protocol number 88 (EIGRP) [15]. 9. References 9.1. Normative References [1] Bradner, S., "Key words for use in RFCs to Indicate Requirement Levels", BCP 14, RFC 2119, DOI 10.17487/RFC2119, March 1997, . [2] Garcia-Luna-Aceves, J.J., "A Unified Approach to Loop-Free Routing Using Distance Vectors or Link States", SIGCOMM '89, Symposium proceedings on Communications architectures & protocols, Volume 19, pages 212-223, ACM 089791-332-9/89/0009/0212, DOI 10.1145/75247.75268, 1989. [3] Garcia-Luna-Aceves, J.J., "Loop-Free Routing using Diffusing Computations", Network Information Systems Center, SRI International, appeared in IEEE/ACM Transactions on Networking, Vol. 1, No. 1, DOI 10.1109/90.222913, 1993. [4] Rosen, E. and Y. Rekhter, "IANA Registries for BGP Extended Communities", RFC 7153, DOI 10.17487/RFC7153, March 2014, . Savage, et al. Informational [Page 77] RFC 7868 Cisco's EIGRP May 2016 [5] Narten, T., "Assigning Experimental and Testing Numbers Considered Useful", BCP 82, RFC 3692, DOI 10.17487/RFC3692, January 2004, . [6] Kelly, S. and S. Frankel, "Using HMAC-SHA-256, HMAC-SHA-384, and HMAC-SHA-512 with IPsec", RFC 4868, DOI 10.17487/RFC4868, May 2007, . [7] Deering, S., "Host extensions for IP multicasting", STD 5, RFC 1112, DOI 10.17487/RFC1112, August 1989, . [8] Postel, J., "Internet Protocol", STD 5, RFC 791, DOI 10.17487/RFC0791, September 1981, . [9] Deering, S. and R. Hinden, "Internet Protocol, Version 6 (IPv6) Specification", RFC 2460, DOI 10.17487/RFC2460, December 1998, . 9.2. Informative References [10] Moy, J., "OSPF Version 2", STD 54, RFC 2328, DOI 10.17487/RFC2328, April 1998, . [11] Clark, A. and B. Claise, "Guidelines for Considering New Performance Metric Development", BCP 170, RFC 6390, DOI 10.17487/RFC6390, October 2011, . [12] IANA, "Address Family Numbers", . [13] IANA, "IPv4 Multicast Address Space Registry", . [14] IANA, "IPv6 Multicast Address Space Registry", . [15] IANA, "Protocol Numbers", . Savage, et al. Informational [Page 78] RFC 7868 Cisco's EIGRP May 2016 Acknowledgments Thank you goes to Dino Farinacci, Bob Albrightson, and Dave Katz. Their significant accomplishments towards the design and development of the EIGRP provided the bases for this document. A special and appreciative thank you goes to the core group of Cisco engineers whose dedication, long hours, and hard work led the evolution of EIGRP over the past decade. They are Donnie Savage, Mickel Ravizza, Heidi Ou, Dawn Li, Thuan Tran, Catherine Tran, Don Slice, Claude Cartee, Donald Sharp, Steven Moore, Richard Wellum, Ray Romney, Jim Mollmann, Dennis Wind, Chris Van Heuveln, Gerald Redwine, Glen Matthews, Michael Wiebe, and others. The authors would like to gratefully acknowledge many people who have contributed to the discussions that lead to the making of this proposal. They include Chris Le, Saul Adler, Scott Van de Houten, Lalit Kumar, Yi Yang, Kumar Reddy, David Lapier, Scott Kirby, David Prall, Jason Frazier, Eric Voit, Dana Blair, Jim Guichard, and Alvaro Retana. In addition to the tireless work provided by the Cisco engineers over the years, we would like to personally recognize the teams that created open source versions of EIGRP: o Linux implementation developed by the Quagga team: Jan Janovic, Matej Perina, Peter Orsag, and Peter Paluch. o BSD implementation developed and released by Renato Westphal. Savage, et al. Informational [Page 79] RFC 7868 Cisco's EIGRP May 2016 Authors' Addresses Donnie V. Savage Cisco Systems, Inc. 7025 Kit Creek Rd., RTP, Morrisville, NC 27560 United States Phone: 919-392-2379 Email: dsavage@cisco.com James Ng Cisco Systems, Inc. 7025 Kit Creek Rd., RTP, Morrisville, NC 27560 United States Phone: 919-392-2582 Email: jamng@cisco.com Steven Moore Cisco Systems, Inc. 7025 Kit Creek Rd., RTP, Morrisville, NC 27560 United States Phone: 408-895-2031 Email: smoore@cisco.com Donald Slice Cumulus Networks Apex, NC United States Email: dslice@cumulusnetworks.com Peter Paluch University of Zilina Univerzitna 8215/1, Zilina 01026 Slovakia Phone: 421-905-164432 Email: Peter.Paluch@fri.uniza.sk Russ White LinkedIn Apex, NC United States Phone: 1-877-308-0993 Email: russw@riw.us Savage, et al. Informational [Page 80]