Internet Engineering Task Force (IETF) X. Li Request for Comments: 6219 C. Bao Category: Informational M. Chen ISSN: 2070-1721 H. Zhang J. Wu CERNET Center/Tsinghua University May 2011 The China Education and Research Network (CERNET) IVI Translation Design and Deployment for the IPv4/IPv6 Coexistence and Transition Abstract This document presents the China Education and Research Network (CERNET)'s IVI translation design and deployment for the IPv4/IPv6 coexistence and transition. The IVI is a prefix-specific and stateless address mapping mechanism for "an IPv6 network to the IPv4 Internet" and "the IPv4 Internet to an IPv6 network" scenarios. In the IVI design, subsets of the ISP's IPv4 addresses are embedded in the ISP's IPv6 addresses, and the hosts using these IPv6 addresses can therefore communicate with the global IPv6 Internet directly and can communicate with the global IPv4 Internet via stateless translators. The communications can either be IPv6 initiated or IPv4 initiated. The IVI mechanism supports the end-to-end address transparency and incremental deployment. The IVI is an early design deployed in the CERNET as a reference for the IETF standard documents on IPv4/IPv6 stateless translation. Status of This Memo This document is not an Internet Standards Track specification; it is published for informational purposes. This document is a product of the Internet Engineering Task Force (IETF). It represents the consensus of the IETF community. It has received public review and has been approved for publication by the Internet Engineering Steering Group (IESG). Not all documents approved by the IESG are a candidate for any level of Internet Standard; see Section 2 of RFC 5741. Information about the current status of this document, any errata, and how to provide feedback on it may be obtained at http://www.rfc-editor.org/info/rfc6219. Li, et al. Informational [Page 1] RFC 6219 CERNET IVI Translation Design May 2011 Copyright Notice Copyright (c) 2011 IETF Trust and the persons identified as the document authors. All rights reserved. This document is subject to BCP 78 and the IETF Trust's Legal Provisions Relating to IETF Documents (http://trustee.ietf.org/license-info) in effect on the date of publication of this document. Please review these documents carefully, as they describe your rights and restrictions with respect to this document. Code Components extracted from this document must include Simplified BSD License text as described in Section 4.e of the Trust Legal Provisions and are provided without warranty as described in the Simplified BSD License. Table of Contents 1. Introduction ....................................................3 1.1. Analysis of IPv4-IPv6 Translation Mechanisms ...............3 1.2. CERNET Translation Requirements ............................4 2. Terms and Abbreviations .........................................6 3. The IVI Translation Algorithm ...................................6 3.1. Address Format .............................................8 3.2. Routing and Forwarding .....................................9 3.3. Network-Layer Header Translation ..........................10 3.4. Transport-Layer Header Translation ........................11 3.5. Fragmentation and MTU Handling ............................11 3.6. ICMP Handling .............................................11 3.7. Application Layer Gateway .................................12 4. The IVI DNS Configuration ......................................12 4.1. DNS Configuration for the IVI6(i) Addresses ...............12 4.2. DNS Service for the IVIG6(i) Addresses ....................12 5. The Advanced IVI Translation Functions .........................12 5.1. IVI Multicast .............................................12 6. IVI Host Operation .............................................13 6.1. IVI Address Assignment ....................................13 6.2. IPv6 Source Address Selection .............................13 7. The IVI Implementation .........................................14 7.1. Linux Implementation ......................................14 7.2. Testing Environment .......................................14 8. Security Considerations ........................................14 9. Contributors ...................................................15 10. Acknowledgments ...............................................15 Appendix A. The IVI Translator Configuration Example ..............16 Appendix B. The traceroute Results ................................17 11. References ....................................................19 11.1. Normative References .....................................19 11.2. Informative References ...................................20 Li, et al. Informational [Page 2] RFC 6219 CERNET IVI Translation Design May 2011 1. Introduction This document presents the CERNET IVI translation design and deployment for the IPv4/IPv6 coexistence and transition. In Roman numerals, the "IV" stands for 4, and "VI" stands for 6, so "IVI" stands for the IPv4/IPv6 translation. The experiences with IPv6 deployment in the past 10 years indicate that the ability to communicate between IPv4 and IPv6 address families would be beneficial. However, the current transition methods do not fully support this requirement [RFC4213]. For example, dual-stack hosts can communicate with both the IPv4 and IPv6 hosts, but single-stack hosts can only communicate with hosts in the same address family. While the dual-stack approach continues to work in many cases even in the face of IPv4 address depletion [COUNT], there are situations where it would be desirable to communicate with a device in another address family. Tunneling-based architectures can link the IPv6 islands across IPv4 networks, but they cannot provide communication between the two different address families [RFC3056] [RFC5214] [RFC4380]. Translation can relay communications for hosts located in IPv4 and IPv6 networks, but the current implementation of this kind of architecture is not scalable, and it cannot maintain end-to-end address transparency [RFC2766] [RFC3142] [RFC4966] [RFC2775]. 1.1. Analysis of IPv4-IPv6 Translation Mechanisms Since IPv4 and IPv6 are different protocols with different addressing structures, a translation mechanism is necessary for communication between endpoints using different address families. There are several ways to implement the translation. One is the Stateless IP/ ICMP Translation Algorithm (SIIT) [RFC2765], which provides a mechanism for translation between IPv4 and IPv6 packet headers (including ICMP headers) without requiring any per-connection state. However, SIIT does not specify the address assignment and routing scheme [RFC2766]. For example, SIIT uses IPv4-mapped IPv6 addresses [::ffff:ipv4-addr/96] and IPv4-compatible IPv6 addresses [::ipv4-address/96] for the address mapping, but these addresses violate the aggregation principle of IPv6 routing [RFC4291]. The other translation mechanism is Network Address Translation - Protocol Translation (NAT-PT), which has serious technical and operational difficulties; the IETF has reclassified it from Proposed Standard to Historic status [RFC4966]. In order to solve the technical difficulties in NAT-PT, the issues and the possible workarounds are: Li, et al. Informational [Page 3] RFC 6219 CERNET IVI Translation Design May 2011 1. NAT-PT disrupts all protocols that embed IP addresses (and/or ports) in packet payloads. There is little that can be done about this, other than using Application Layer Gateways (ALGs) or preferring protocols that transport DNS names instead of addresses. 2. Loss of end-to-end address transparency may occur. End-to-end address transparency implies a global address space, the ability to pass packets unaltered throughout the network, and the ability to use source and destination addresses as unique labels [RFC2775]. A reversible, algorithmic mapping can restore some of this transparency. However, it is still not possible to ensure that all nodes in the existing Internet support such reversible mappings. 3. The states maintained in the translator cause scalability, multihoming, and load-sharing problems. Hence, a stateless translation scheme is preferred. 4. Loss of information due to incompatible semantics between IPv4 and IPv6 versions of headers and protocols may occur. A partial remedy to this is the proper attention to the details of the protocol translation, for example, the error-codes mapping between ICMP and ICMPv6. However, some semantic differences remain. 5. The DNS is tightly coupled with the translator and lack of address mapping persistence discussed in Section 3.3 of [RFC4966]. Hence, the DNS should be decoupled from the translator. 6. Support for referrals is difficult in NAT-PT, given that translated addresses may leak outside the network where these addresses have a meaning. Stateless translation, algorithmic address mappings, and the decoupling of DNS from the translation process can help the handling of referrals. Nevertheless, it is still possible that an address-based referral is passed to someone who cannot employ it. For instance, an IPv6-only node may pass a referral based on an IPv6 address to a node that only understands IPv4. 1.2. CERNET Translation Requirements The China Education and Research Network has two backbones using different address families. The CERNET is IPv4-only [CERNET] and CERNET2 is IPv6-only [CNGI-CERNET2], which fit in "an IPv6 network to the IPv4 Internet" and "the IPv4 Internet to an IPv6 network" scenarios in the IETF BEHAVE working group definition [BEHAVE] Li, et al. Informational [Page 4] RFC 6219 CERNET IVI Translation Design May 2011 [RFC6144]. In order to make CERNET2 communicate with the IPv4 Internet, we designed the IVI mechanism and installed IVI translators between the CERNET and CERNET2. The requirements of the IVI mechanism are: 1. It should support both IPv6-initiated and IPv4-initiated communications for the IPv6 clients/servers in "an IPv6 network". 2. It should follow current IPv4 and IPv6 routing practice without increasing the global routing table size in both address families. 3. It should be able to be deployed incrementally. 4. It should be able to use IPv4 addresses effectively due to the IPv4 address depletion problem. 5. It should be stateless to achieve scalability. 6. The DNS function should be decoupled from the translator. The specific IVI design presented in this document can satisfy the above requirements, with the following notes: 1. It restricts the IPv6 hosts to use a subset of the addresses inside the ISP's IPv6 block. Therefore, IPv6 autoconfiguration cannot be used for these IPv6 hosts. Manual configuration or autoconfiguration via stateful DHCPv6 is required. 2. It defines a one-to-one mapping between IPv4 addresses and IPv6 addresses; hence, the IPv4 addresses cannot be used efficiently. However, the IVI6 addresses can be used both for IPv6 clients and IPv6 servers. Due to this limitation, we suggest using IVI6 addresses for servers. 3. An ALG is still required for any applications that embed address(es) in the payload. 4. Some issues with end-to-end transparency, address referrals, and incompatible semantics between protocol versions still remain, as discussed above. The IVI is an early design deployed in the CERNET for the stateless translation. The IETF standard IPv4-IPv6 stateless and stateful translation mechanisms are defined in [RFC6144], [RFC6052], [RFC6145], [RFC6146], and [RFC6147]. Li, et al. Informational [Page 5] RFC 6219 CERNET IVI Translation Design May 2011 2. Terms and Abbreviations The following terms and abbreviations are used in this document: ISP(i): A specific Internet service provider "i". IVIG4: The global IPv4 address space. IPS4(i): A subset of IVIG4 allocated to ISP(i). IVI4(i): A subset of IPS4(i); the addresses in this set will be mapped to IPv6 via the IVI mapping mechanism and used by IPv6 hosts of ISP(i). IPG6: The global IPv6 address space. IPS6(i): A subset of IPG6 allocated to ISP(i). IVIG6(i): A subset of IPS6(i), and an image of IVIG4 in the IPv6 address family via the IVI mapping mechanism. It is defined as the IPv4-converted address in [RFC6144]. IVI6(i): A subset of IVIG6(i) and an image of IVI4(i) in the IPv6 address family via the IVI mapping mechanism. It is defined as the IPv4-translatable address in [RFC6144]. IVI translator: The mapping and translation gateway between IPv4 and IPv6 based on the IVI mechanism. IVI DNS: Providing the IVI Domain Name System (DNS). The key words "MUST", "MUST NOT", "REQUIRED", "SHALL", "SHALL NOT", "SHOULD", "SHOULD NOT", "RECOMMENDED", "MAY", and "OPTIONAL", when they appear in this document, are to be interpreted as described in [RFC2119]. 3. The IVI Translation Algorithm The IVI is a prefix-specific and stateless address mapping scheme that can be carried out by individual ISPs. In the IVI design, subsets of the ISP's IPv4 addresses are embedded in the ISP's IPv6 addresses, and the hosts using these IPv6 addresses can therefore communicate with the global IPv6 Internet directly and can communicate with the global IPv4 Internet via stateless translators. The communications can either be IPv6 initiated or IPv4 initiated. Li, et al. Informational [Page 6] RFC 6219 CERNET IVI Translation Design May 2011 The IVI mapping and translation mechanism is implemented in an IVI translator that connects between "an IPv6 network" and the IPv4 Internet via the ISP's IPv4 network, as shown in the following figure. ------ ----- ------ / The \ ----- / An \ / The \ | IPv4 |-----|Xlate|------| IPv6 |-----| IPv6 | \Internet/ ----- \Network/ \Internet/ ------ ----- ------ <===> Figure 1: The Scenarios: "An IPv6 Network to the IPv4 Internet" and "the IPv4 Internet to an IPv6 Network" In order to perform the translation function between IPv4 and IPv6 addresses, the translator needs to represent the IPv4 addresses in IPv6 and the IPv6 addresses in IPv4. To represent the IPv4 addresses in IPv6, a unique, prefix-specific, and stateless mapping scheme is defined between IPv4 addresses and subsets of IPv6 addresses, so each provider-independent IPv6 address block (usually a /32) will have a small portion of IPv6 addresses (for example, /40 defined by PREFIX), which is the image of the totality of the global IPv4 addresses, as shown in the following figure. The SUFFIX is all zeros. +-+-+-+-+-+-+ | IVIG4 | +-+-+-+-+-+-+ || \ / \/ +--+--+--+--+--+--+--+--+--+--+--+--+--+--+--+--+ | PREFIX | IPv4 addr | SUFFIX | +--+--+--+--+--+--+--+--+--+--+--+--+--+--+--+--+ Figure 2: Representing the IPv4 Addresses in IPv6 Li, et al. Informational [Page 7] RFC 6219 CERNET IVI Translation Design May 2011 To represent the IPv6 addresses in IPv4, each provider can borrow a portion of its IPv4 addresses and map them into IPv6 based on the above mapping rule. These special IPv6 addresses will be physically used by IPv6 hosts. The original IPv4 form of the borrowed addresses is the image of these special IPv6 addresses, and it can be accessed by the IPv4 Internet, as shown in the following figure. The SUFFIX can either be all zeros, or some other value for future extensions. +--+--+--+--+--+--+--+--+--+--+--+--+--+--+--+--+ | PREFIX | |IVI4| | SUFFIX | +--+--+--+--+--+--+--+--+--+--+--+--+--+--+--+--+ || \ / \/ -+-+-+ |IVI4| -+-+-+ Figure 3: Representing the IPv6 Addresses in IPv4 3.1. Address Format The IVI address format is defined based on an individual ISP's IPv6 prefix, as shown in the following figure | 0 |32 |40 |72 127| ------------------------------------------------------------------ | |ff | | | ------------------------------------------------------------------ |<- PREFIX ->|<- IPv4 address ->| <- SUFFIX -> | Figure 4: IVI Address Mapping where bit 0 to bit 31 are the prefix of ISP(i)'s /32 (e.g., using document IPv6 address IPS6=2001:db8::/32) in the CERNET implementation, bit 32 to bit 39 are all ones as the identifier of the IVI addresses, and bit 40 to bit 71 are embedded global IPv4 space (IVIG4), presented in hexadecimal format (e.g., 2001:db8:ff00::/40). Note that based on the IVI mapping mechanism, an IPv4 /24 is mapped to an IPv6 /64, and an IPv4 /32 is mapped to an IPv6 /72. The IETF standard for the address format is defined in [RFC6052]. Li, et al. Informational [Page 8] RFC 6219 CERNET IVI Translation Design May 2011 3.2. Routing and Forwarding Based on the IVI address mapping rule, routing is straightforward, as shown in the following figure /-----\ /-----\ ( ISP's ) -- 192.0.2.2 ----------- 2001:db8::2 -- ( ISP's ) ( IPv4 )--|R1|-------------| IVI Xlate |------------|R2|---( IPv6 ) (network) -- 192.0.2.1 ----------- 2001:db8::1 -- (network) \-----/ \-----/ | | | | The IPv4 Internet The IPv6 Internet Figure 5: IVI Routing where 1. IVI Xlate is a special dual-stack router, with two interfaces, one to the IPv4 network and the other to the IPv6 network (it is also possible to have a single interface configured with both IPv4 and IPv6 addresses). IVI Xlate can support dynamic routing protocols in IPv4 and IPv6 address families. In the above configuration, the static routing configuration can be used. 2. Router R1 has an IPv4 route for IVI4(i)/k (k is the prefix length of IVI4(i)) with the next hop equal to 192.0.2.1, and this route is distributed to the Internet with proper aggregation. 3. Router R2 has an IPv6 route for IVIG6(i)/40 with the next hop equal to 2001:db8::1, and this route is distributed to the IPv6 Internet with proper aggregation. 4. The IVI translator has an IPv6 route for IVI6(i)/(40+k) with the next hop equal to 2001:db8::2. The IVI translator also has an IPv4 default route 0.0.0.0/0 with the next hop equal to 192.0.2.2. Note that the routes described above can be learned/inserted by dynamic routing protocols (IGP or BGP) in the IVI translator peering with R1 and R2. Since both IVI4(i) and IVI6(i) are aggregated to IPS4(i) and IPS6(i) in ISP(i)'s border routers, respectively, they will not affect the global IPv4 and IPv6 routing tables [RFC4632]. Since the IVI translation is stateless, it can support multihoming when the same prefix is used for multiple translators. Li, et al. Informational [Page 9] RFC 6219 CERNET IVI Translation Design May 2011 Since the IVI translation can be implemented independently in each ISP's network, it can be incrementally deployed in the global Internet. 3.3. Network-Layer Header Translation IPv4 [RFC0791] and IPv6 [RFC2460] are different protocols with different network-layer header formats; the translation of the IPv4 and IPv6 headers MUST be performed according to SIIT [RFC2765], except for the source and destination addresses in the header, as shown in the following figures. ------------------------------------------------------------- IPv4 Field Translated to IPv6 ------------------------------------------------------------- Version (0x4) Version (0x6) IHL discarded Type of Service Traffic Class Total Length Payload Length = Total Length - 20 Identification discarded Flags discarded Offset discarded TTL Hop Limit Protocol Next Header Header Checksum discarded Source Address IVI address mapping Destination Address IVI address mapping Options discarded ------------------------------------------------------------- Figure 6: IPv4-to-IPv6 Header Translation ------------------------------------------------------------- IPv6 Field Translated to IPv4 Header ------------------------------------------------------------- Version (0x6) Version (0x4) Traffic Class Type of Service Flow Label discarded Payload Length Total Length = Payload Length + 20 Next Header Protocol Hop Limit TTL Source Address IVI address mapping Destination Address IVI address mapping - IHL = 5 - Header Checksum recalculated ------------------------------------------------------------- Figure 7: IPv6-to-IPv4 Header Translation Li, et al. Informational [Page 10] RFC 6219 CERNET IVI Translation Design May 2011 The IETF standard for IP/ICMP translation is defined in [RFC6145], which contains updated technical specifications. 3.4. Transport-Layer Header Translation Since the TCP and UDP headers [RFC0793] [RFC0768] consist of checksums that include the IP header, the recalculation and updating of the transport-layer headers MUST be performed. Note that SIIT does not recalculate the transport-layer checksum, since checksum- neutral IPv6 addresses are used in SIIT [RFC2765]. The IETF standard for transport-layer header translation is defined in [RFC6145], which contains updated technical specifications. 3.5. Fragmentation and MTU Handling When the packet is translated by the IVI translator, due to the different sizes of the IPv4 and IPv6 headers, the IVI6 packets will be at least 20 bytes larger than the IVI4 packets, which may exceed the MTU of the next link in the IPv6 network. Therefore, the MTU handling and translation between IPv6 fragmentation headers and the fragmentation field in the IPv4 headers are necessary; this is performed in the IVI translator according to SIIT [RFC2765]. The IETF standard for fragmentation and MTU handling is defined in [RFC6145], which contains updated technical specifications. 3.6. ICMP Handling For ICMP message translation between IPv4 and IPv6, IVI follows the ICMP/ICMPv6 message correspondence as defined in SIIT [RFC2765]. Note that the ICMP message may be generated by an intermediate router whose IPv6 address does not belong to IVIG6(i). Since ICMP translation is important to the path MTU discovery and troubleshooting, the IPv4 representation of the non-IVIG6 addresses in the ICMP packets is required. In the current IVI prototype, a small IPv4 address block is used to identify the non-IVIG6 addresses. This prevents translated ICMP messages from being discarded due to unknown or private IP sources. The IETF standard for IP/ICMP translation is defined in [RFC6145], which contains updated technical specifications. Li, et al. Informational [Page 11] RFC 6219 CERNET IVI Translation Design May 2011 3.7. Application Layer Gateway Due to the features of 1-to-1 address mapping and stateless operation, IVI can support most of the existing applications, such as HTTP, Secure SHell (SSH), and Telnet. However, some applications are designed such that IP addresses are used to identify application- layer entities (e.g., FTP). In these cases, an Application Layer Gateway (ALG) is unavoidable, and it can be integrated into the IVI translator. The discussion of the use of ALGs is in [RFC6144]. 4. The IVI DNS Configuration The DNS [RFC1035] service is important for the IVI mechanism. 4.1. DNS Configuration for the IVI6(i) Addresses For providing authoritative DNS service for IVI4(i) and IVI6(i), each host name will have both an A record and a AAAA record pointing to IVI4(i) and IVI6(i), respectively. Note that the same name always points to a unique host, which is an IVI6(i) host, and it has IVI4(i) representation via the IVI translator. 4.2. DNS Service for the IVIG6(i) Addresses For resolving the IPv6 form of the global IPv4 space (IVIG6(i)), each ISP must provide customized IVI DNS service for the IVI6(i) hosts. The IVI DNS server MUST be deployed in a dual-stack environment. When the IVI6(i) host queries a AAAA record for an IPv4-only domain name, the IVI DNS will query the AAAA record first. If the AAAA record does not exist, the IVI DNS will query the A record and map it to IVIG6(i), and return a AAAA record to the IVI6(i) host. The technical specifications for this process are defined in [RFC6147]. 5. The Advanced IVI Translation Functions 5.1. IVI Multicast The IVI mechanism can support IPv4/IPv6 communication of Protocol Independent Multicast - Source-Specific Multicast (PIM-SSM) [RFC5771] [RFC3569] [RFC4607]. There will be 2^24 group addresses for IPv4 SSM. The corresponding IPv6 SSM group addresses can be defined as shown in the following figure. Li, et al. Informational [Page 12] RFC 6219 CERNET IVI Translation Design May 2011 ------------------------------------------------------- IPv4 Group Address IPv6 Group Address ------------------------------------------------------- 232.0.0.0/8 ff3e:0:0:0:0:0:f000:0000/96 232.255.255.255/8 ff3e:0:0:0:0:0:f0ff:ffff/96 ------------------------------------------------------- Figure 8: IVI Multicast Group Address Mapping The source address in IPv6 MUST be IVI6(i) in order to perform Reverse Path Forwarding (RPF) as required by PIM - Sparse Mode (PIM-SM). The interoperation of PIM-SM for IPv4 and IPv6 address families can either be implemented via an Application Layer Gateway or via static joins based on IGMPv3 and Multicast Listener Discovery Version 2 (MLDv2) in IPv4 and IPv6, respectively. 6. IVI Host Operation 6.1. IVI Address Assignment The IVI6 address has a special format (for example, IVI4=192.0.2.1/32 and IVI6=2001:db8:ffc0:2:100::/72); therefore, stateless IPv6 address autoconfiguration cannot be used. However, the IVI6 can be assigned to the IPv6 end system via manual configuration or stateful autoconfiguration via DHCPv6. o For the manual configuration, the host needs to configure the IVI6 address and the corresponding prefix length, as well as the default gateway address and the DNS resolver address. o For the DHCPv6 configuration, the DHCPv6 will assign the IVI6 address and the DNS resolver address to the host. The router in the subnet should enable router advertisement (RA), since the default gateway is learned from the router. 6.2. IPv6 Source Address Selection Since each IPv6 host may have multiple addresses, it is important for the host to use an IVI6(i) address to reach the global IPv4 networks. The short-term workaround is to use IVI6(i) as the default source IPv6 address of the host, defined as the policy table in [RFC3484]. The long-term solution requires that the application should be able to select the source addresses for different services. Li, et al. Informational [Page 13] RFC 6219 CERNET IVI Translation Design May 2011 7. The IVI Implementation 7.1. Linux Implementation An implementation of IVI exists for the Linux operating system. The source code can be downloaded from [LINUX]. An example of how to configure an IVI deployment is shown in Appendix A. The IVI DNS source code for the IVIG6(i) addresses presented in this document can be downloaded from [DNS]. 7.2. Testing Environment The IVI translator based on the Linux implementation has been deployed between [CERNET] (IPv4-only) and [CNGI-CERNET2] (IPv6-only) since March 2006. The pure-IPv6 web servers using IVI6 addresses [2001:250:ffca:2672:100::] behind the IVI translator can be accessed by the IPv4 hosts [TEST4], and also by the global IPv6 hosts [TEST6]. The pure-IPv6 clients using IVI6 addresses behind the IVI translator can access IPv4 servers on the IPv4 Internet. Two traceroute results are presented in Appendix B to show the address mapping of the IVI mechanism. IVI6 manual configuration and DHCPv6 configuration of the IPv6 end system have also been tested with success. 8. Security Considerations This document presents the prefix-specific and stateless address mapping mechanism (IVI) for the IPv4/IPv6 coexistence and transition. The IPv4 security and IPv6 security issues should be addressed by related documents of each address family and are not included in this document. However, there are several issues that need special considerations, specifically (a) IPsec and its NAT traversal, (b) DNS Security Extensions (DNSSEC), and (c) firewall filter rules. o IPsec and its NAT traversal: Since the IVI scheme maintains end- to-end address transparency, IPsec could work with or without NAT traversal techniques. o DNSSEC: DNSSEC verification will be terminated at the IVI DNS for the "A record to AAAA record" translation. It would be fine to have a translation in a local IVI DNS server that also verifies Li, et al. Informational [Page 14] RFC 6219 CERNET IVI Translation Design May 2011 DNSSEC, or in the host, if the host both translates the DNS entry and again verifies DNSSEC validity. The DNSSEC discussion is in [RFC6147]. o Firewall filter rules: Since the IVI scheme maintains the end-to- end address transparency and there is a unique mapping between IPv4 and IPv6 addresses, the firewall filter rule can therefore be implemented for one address family, or mapped to another address family and implemented in that address family. However, the current IPv6 routers may only support the access-list or uRPF (unicast Reverse Path Forwarding) for the prefix length shorter than /64; there may a practical constraint for the construction of such rules. Except for the issues discussed above, we have not found special security problems introduced by the IVI translation in our experiments. 9. Contributors The authors would like to acknowledge the following contributors in the different phases of the IVI development: Ang Li, Yuncheng Zhu, Junxiu Lu, Yu Zhai, Wentao Shang, Weifeng Jiang, and Bizheng Fu. The authors would like to acknowledge the following contributors, who provided helpful inputs concerning the IVI concept: Bill Manning, David Ward, Elwyn Davies, Lixia Zhang, Jun Murai, Fred Baker, Jari Arkko, Ralph Droms, Tony Hain, and Kevin Yin. 10. Acknowledgments The authors thank the following for funding support: the CERNET, CNGI-CERNET2, CNGI Research and Development, and the China "863" and China "973" projects. Li, et al. Informational [Page 15] RFC 6219 CERNET IVI Translation Design May 2011 Appendix A. The IVI Translator Configuration Example #!/bin/bash # open forwarding echo 1 > /proc/sys/net/ipv6/conf/all/forwarding echo 1 > /proc/sys/net/ipv4/conf/all/forwarding # config route for IVI6 = 2001:db8:ffc0:2:0::/64, # IVI4 = 192.0.2.0/24 # configure IPv6 route route add -A inet6 2001:db8:ffc0:2:0::/64 \ gw 2001:da8:aaae::206 dev eth0 # config mapping for source-PF = 2001:db8::/32 # config mapping for destination-PF = 2001:db8::/32 # for each mapping, a unique pseudo-address (10.0.0.x/8) # should be configured. # ip addr add 10.0.0.1/8 dev eth0 # IPv4-to-IPv6 mapping: multiple mappings can be done via multiple # commands. # mroute IVI4-network IVI4-mask pseudo-address interface \ # source-PF destination-PF /root/mroute 192.0.2.0 255.255.255.0 10.0.0.1 \ eth0 2001:db8:: 2001:db8:: # IPv6-to-IPv4 mapping # mroute6 destination-PF destination-PF-pref-len /root/mroute6 2001:db8:ff00:: 40 Figure 9: IVI Configuration Example Li, et al. Informational [Page 16] RFC 6219 CERNET IVI Translation Design May 2011 Appendix B. The traceroute Results ivitraceroute 202.38.108.2 1 202.112.0.65 6 ms 2 ms 1 ms 2 202.112.53.73 4 ms 6 ms 12 ms 3 202.112.53.178 1 ms 1 ms 1 ms 4 202.112.61.242 1 ms 1 ms 1 ms 5 192.0.2.100 1 ms 1 ms 1 ms 6 192.0.2.102 1 ms 1 ms 1 ms 7 192.0.2.103 2 ms 2 ms 2 ms 8 192.0.2.104 2 ms 2 ms 2 ms 9 192.0.2.105 4 ms 4 ms 3 ms 10 202.38.108.2 2 ms 3 ms 3 ms Figure 10: ivitraceroute Results Note that the non-IVIG6 addresses are mapped to IPv4 document address 192.0.2.0/24. Li, et al. Informational [Page 17] RFC 6219 CERNET IVI Translation Design May 2011 ivitraceroute6 www.mit.edu src_ivi4=202.38.97.205 src_ivi6=2001:da8:ffca:2661:cd00:: dst_host=www.mit.edu dst_ip4=18.7.22.83 dst_ivig=2001:da8:ff12:716:5300:: traceroute to 2001:da8:ff12:716:5300:: (2001:da8:ff12:716:5300::), 30 hops max, 40 byte packets to not_ivi 1 2001:da8:ff0a:0:100:: 0.304 ms 0.262 ms 0.190 ms 10.0.0.1 2 2001:da8:ffca:7023:fe00:: 0.589 ms * * 202.112.35.254 3 2001:da8:ffca:7035:4900:: 1.660 ms 1.538 ms 1.905 ms 202.112.53.73 4 2001:da8:ffca:703d:9e00:: 0.371 ms 0.530 ms 0.459 ms 202.112.61.158 5 2001:da8:ffca:7035:1200:: 0.776 ms 0.704 ms 0.690 ms 202.112.53.18 6 2001:da8:ffcb:b5c2:7d00:: 89.382 ms 89.076 ms 89.240 ms 203.181.194.125 7 2001:da8:ffc0:cb74:9100:: 204.623 ms 204.685 ms 204.494 ms 192.203.116.145 8 2001:da8:ffcf:e7f0:8300:: 249.842 ms 249.945 ms 250.329 ms 207.231.240.131 9 2001:da8:ff40:391c:2d00:: 249.891 ms 249.936 ms 250.090 ms 64.57.28.45 10 2001:da8:ff40:391c:2a00:: 259.030 ms 259.110 ms 259.086 ms 64.57.28.42 11 2001:da8:ff40:391c:700:: 264.247 ms 264.399 ms 264.364 ms 64.57.28.7 12 2001:da8:ff40:391c:a00:: 271.014 ms 269.572 ms 269.692 ms 64.57.28.10 13 2001:da8:ffc0:559:dd00:: 274.300 ms 274.483 ms 274.316 ms 192.5.89.221 14 2001:da8:ffc0:559:ed00:: 274.534 ms 274.367 ms 274.517 ms 192.5.89.237 15 * * * 16 2001:da8:ff12:a800:1900:: 276.032 ms 275.876 ms 276.090 ms 18.168.0.25 17 2001:da8:ff12:716:5300:: 276.285 ms 276.370 ms 276.214 ms 18.7.22.83 Figure 11: ivitraceroute6 Results Note that all of the IPv4 addresses can be mapped to prefix-specific IPv6 addresses (for example, 18.7.22.83 is mapped to 2001:da8:ff12: 716:5300::). Li, et al. Informational [Page 18] RFC 6219 CERNET IVI Translation Design May 2011 11. References 11.1. Normative References [RFC0768] Postel, J., "User Datagram Protocol", STD 6, RFC 768, August 1980. [RFC0791] Postel, J., "Internet Protocol", STD 5, RFC 791, September 1981. [RFC0793] Postel, J., "Transmission Control Protocol", STD 7, RFC 793, September 1981. [RFC1035] Mockapetris, P., "Domain names - implementation and specification", STD 13, RFC 1035, November 1987. [RFC2119] Bradner, S., "Key words for use in RFCs to Indicate Requirement Levels", BCP 14, RFC 2119, March 1997. [RFC2460] Deering, S. and R. Hinden, "Internet Protocol, Version 6 (IPv6) Specification", RFC 2460, December 1998. [RFC2765] Nordmark, E., "Stateless IP/ICMP Translation Algorithm (SIIT)", RFC 2765, February 2000. [RFC2766] Tsirtsis, G. and P. Srisuresh, "Network Address Translation - Protocol Translation (NAT-PT)", RFC 2766, February 2000. [RFC3056] Carpenter, B. and K. Moore, "Connection of IPv6 Domains via IPv4 Clouds", RFC 3056, February 2001. [RFC4213] Nordmark, E. and R. Gilligan, "Basic Transition Mechanisms for IPv6 Hosts and Routers", RFC 4213, October 2005. [RFC4291] Hinden, R. and S. Deering, "IP Version 6 Addressing Architecture", RFC 4291, February 2006. [RFC4380] Huitema, C., "Teredo: Tunneling IPv6 over UDP through Network Address Translations (NATs)", RFC 4380, February 2006. [RFC4607] Holbrook, H. and B. Cain, "Source-Specific Multicast for IP", RFC 4607, August 2006. [RFC4632] Fuller, V. and T. Li, "Classless Inter-domain Routing (CIDR): The Internet Address Assignment and Aggregation Plan", BCP 122, RFC 4632, August 2006. Li, et al. Informational [Page 19] RFC 6219 CERNET IVI Translation Design May 2011 [RFC5214] Templin, F., Gleeson, T., and D. Thaler, "Intra-Site Automatic Tunnel Addressing Protocol (ISATAP)", RFC 5214, March 2008. [RFC5771] Cotton, M., Vegoda, L., and D. Meyer, "IANA Guidelines for IPv4 Multicast Address Assignments", BCP 51, RFC 5771, March 2010. [RFC6052] Bao, C., Huitema, C., Bagnulo, M., Boucadair, M., and X. Li, "IPv6 Addressing of IPv4/IPv6 Translators", RFC 6052, October 2010. [RFC6144] Baker, F., Li, X., Bao, C., and K. Yin, "Framework for IPv4/IPv6 Translation", RFC 6144, April 2011. [RFC6145] Li, X., Bao, C., and F. Baker, "IP/ICMP Translation Algorithm", RFC 6145, April 2011. [RFC6146] Bagnulo, M., Matthews, P., and I. van Beijnum, "Stateful NAT64: Network Address and Protocol Translation from IPv6 Clients to IPv4 Servers", RFC 6146, April 2011. [RFC6147] Bagnulo, M., Sullivan, A., Matthews, P., and I. van Beijnum, "DNS64: DNS Extensions for Network Address Translation from IPv6 Clients to IPv4 Servers", RFC 6147, April 2011. 11.2. Informative References [BEHAVE] "The IETF Behave Working Group Charter: http://datatracker.ietf.org/wg/behave/charter/". [CERNET] "CERNET Homepage: http://www.edu.cn/english_1369/index.shtml". [CNGI-CERNET2] "CNGI-CERNET2 Homepage: http://www.cernet2.edu.cn/index_en.htm". [COUNT] "IPv4 address countdown: http://penrose.uk6x.com/". [DNS] "Source Code of the IVI DNS http://www.ivi2.org/IVI/src/ividns-0.1.tar.gz/". [LINUX] "Source Code of the IVI implementation for Linux: http://linux.ivi2.org/impl/". Li, et al. Informational [Page 20] RFC 6219 CERNET IVI Translation Design May 2011 [RFC2775] Carpenter, B., "Internet Transparency", RFC 2775, February 2000. [RFC3142] Hagino, J. and K. Yamamoto, "An IPv6-to-IPv4 Transport Relay Translator", RFC 3142, June 2001. [RFC3484] Draves, R., "Default Address Selection for Internet Protocol version 6 (IPv6)", RFC 3484, February 2003. [RFC3569] Bhattacharyya, S., Ed., "An Overview of Source-Specific Multicast (SSM)", RFC 3569, July 2003. [RFC4966] Aoun, C. and E. Davies, "Reasons to Move the Network Address Translator - Protocol Translator (NAT-PT) to Historic Status", RFC 4966, July 2007. [TEST4] "Test homepage for the IVI4(i): http://test4.ivi2.org". [TEST6] "Test homepage for the IVI6(i): http://test6.ivi2.org", Available using IPv6 only. Li, et al. Informational [Page 21] RFC 6219 CERNET IVI Translation Design May 2011 Authors' Addresses Xing Li CERNET Center/Tsinghua University Room 225, Main Building, Tsinghua University Beijing 100084 CN Phone: +86 10-62785983 EMail: xing@cernet.edu.cn Congxiao Bao CERNET Center/Tsinghua University Room 225, Main Building, Tsinghua University Beijing 100084 CN Phone: +86 10-62785983 EMail: congxiao@cernet.edu.cn Maoke Chen CERNET Center/Tsinghua University Room 225, Main Building, Tsinghua University Beijing 100084 CN Phone: +86 10-62785983 EMail: fibrib@gmail.com Hong Zhang CERNET Center/Tsinghua University Room 225, Main Building, Tsinghua University Beijing 100084 CN Phone: +86 10-62785983 EMail: neilzh@gmail.com Jianping Wu CERNET Center/Tsinghua University Room 225, Main Building, Tsinghua University Beijing 100084 CN Phone: +86 10-62785983 EMail: jianping@cernet.edu.cn Li, et al. Informational [Page 22]